Release Notes January-March 2023
Archived Release Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending March 31, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Brake Pad Kit - Front (Remove and Replace) - Updated grease in install section.
- Brake Pad Kit - Rear - Mando (Remove and Replace) - Removed faulty image.
- Firmware Reinstall - Touchscreen - Added information on the different types of reinstallations vs. FW versions.
- Fluids - Updated brake fluid recommendation.
- Harness - Body (Remove and Replace) (LHD) - Updated procedure according to the latest time study.
- How To Use This Manual - Added extra information on LH and RH procedures
- Links - Fore - Lower - Front - LH/RH (Remove and Replace) - Added using hub jack adapter for ride height.
- Steering Rack (LHD) (1st Generation) (Remove and Replace) - Added reference to Alignment Tables.
- Steering Rack (RHD) (1st Generation) (Remove and Replace) - Added reference to Alignment Tables.
- Steering Rack (LHD) (2nd Generation) (Remove and Replace) - Added reference to Alignment Tables.
- Steering Rack (RHD) (2nd Generation) (Remove and Replace) - Added reference to Alignment Tables.
Week Ending March 25, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Actuator - Front Passenger's Temperature (Remove and Replace) - Updated procedure to revised validation.
- Drive Unit - Rear - Small (Remove and Replace) - Removed note to exempt North American vehicles from the immobilizer reset.
- How To Use This Manual - Added Nomenclature section to explain variance in naming with firmware/software example.
- HV Battery (AWD) (Remove and Replace) - Updated Discharge section and added steps to configure the HV battery.
- Oil Pump - Front Drive Unit (Remove & Replace) - Updated gearbox fluid type from AFT-9 to EDF2.
Week Ending March 18, 2023
The following procedure(s) were updated:
- Actuator - Driver's Temperature (Remove and Replace) - Updated procedure to revised validation.
- Actuator - Mode (Remove and Replace) - Updated procedure to revised validation.
Week Ending March 11, 2023
The following procedure(s) were updated:
- Halfshaft - Front Drive Unit - LH (1st Generation) (Remove and Replace) - Added a warning for removing the halfshaft.
- Halfshaft - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Added a warning for removing the halfshaft.
- Halfshaft - Front Drive Unit - RH (1st Generation) (Remove and Replace) - Added a warning for removing the halfshaft.
- Halfshaft - Front Drive Unit - RH (2nd Generation) (Remove and Replace) - Added a warning for removing the halfshaft.
- Rear Halfshaft Assembly - Large Drive Unit - LH (Remove and Replace) - Added a warning for removing the halfshaft.
- Rear Halfshaft Assembly - Small Drive Unit - LH (Remove and Replace) - Added a warning for removing the halfshaft.
- Ride Height - Adjust - Fixed errors.
Week Ending March 4, 2023
The following procedure(s) were updated:
- Compressor - Air Suspension (Remove and Replace) - Added note to not replace the K112 relay for vehicles without them.
Week Ending February 25, 2023
The following procedure(s) were updated:
- Actuator - Defrost (Remove and Replace) - Updated to new validation, includes thermal test.
- Actuator - Inlet (Remove and Replace) - Updated to new validation, includes thermal test.
- Brake Rotor - Rear - LH (Remove and Replace) - Updated hyperlink
- Control Arm - Upper - Front - LH (Remove and Replace) - Fixed link to alignment requirement tables.
- Control Arm - Upper - Front - RH (Remove and Replace) - Fixed link to alignment requirement tables.
- Gearbox Fluid - Front Drive Unit (2nd Generation) (Drain and Refill) - Added oil filter replacement note to removal sequence.
- Oil Pump - 3DU Small Rear Drive Unit (Remove and Replace) - Added oil filter replacement note to removal sequence.
- Oil Pump - Front Drive Unit (Remove & Replace) - Added oil filter replacement note to removal sequence.
- - Added oil filter replacement note to removal sequence.
Week Ending February 18, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fluids - Updated information and cautions.
- Grille - Speaker - Rear - LH (Remove and Replace) - Added information for interior ultrasonic sensors.
- Taillight Assembly - LH (Remove and Install) - Updated taillight assembly fastener information.
Week Ending February 11, 2023
The following procedure(s) were updated:
- Oil Pump - 3DU Small Rear Drive Unit (Remove and Replace) - Updated to use of EDF2 gearbox fluid.
- Taillight Assembly - RH (Remove and Replace) - Updated procedure to remove corner bolt, and added installation sequence.
Week Ending February 4, 2023
The following procedure(s) were updated:
- Coolant Heater - Electric - Battery (Remove and Replace) - Added note on HV cable fasteners.
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Added check for high voltage at the fuse.
Week Ending January 28, 2023
The following procedure(s) were updated:
- Disconnect 12V Power - Made procedure consistent with Model 3/Y.
- Seal - Axle - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Update tool used to install front output axle seal to FDU
- Vehicle HV Disablement Procedure - Updated Cautions to Warnings for consistency.
Week Ending January 21, 2023
The following procedure(s) were updated:
- Module - Restraint Control - RCM (Remove and Replace) - Added warnings
- Service Mode Plus - Removed section with Toolbox 2 instructions.
Week Ending January 14, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fender Assembly - Front - LH (Remove and Replace) - Added a step of installing a new motor ID label.
- Four Wheel Alignment Check - Replaced Toolbox 2 panels by Toolbox 3 routines.
- Four Wheel Alignment Check and Adjust - Replaced Toolbox 2 panels by Toolbox 3 routines.
- Liftgate Assembly (Remove and Replace) - Added a step of installing a new motor ID label.
Week Ending January 7, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Cooling System - Partial Refill and Bleed - Reordering reservoir cap steps.
- Cooling System - Vacuum Refill - Replaced Toolbox 2 panels by Toolbox 3 routines.
- HV Rapid Splitter Vehicle Side (Remove and Replace) - Updated to more current validations.
- Module - 2nd Row Seat Controller - LH (Remove and Replace) - Added step to perform firmware reinstall.