Release Notes July-September 2024

Archived Release Notes:

Week Ending September 28, 2024

The following procedure(s) were updated:
  1. SIM Card (Intel based MCU without SIM extender) (Remove and Replace) - Rearranged ESD wrist strap and SIM card installation steps to align with validation.

Week Ending September 21, 2024

The following procedure(s) were updated:
  1. Compressor (Remove and Replace) - Added some missing steps in line with procedure validation.
  2. How To Use This Manual - Added information on the crowsfoot/offset wrench extension calculator.

Week Ending September 14, 2024

The following procedure(s) were updated:
  1. Media Control Unit (Remove and Replace) -
  2. Receiver Dryer and Desiccant (Remove and Replace) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.

Week Ending September 7, 2024

The following procedure(s) were updated:
  1. Key Fob - Program - Added UI pairing steps for Intel vehicles.
  2. Key Fob - Unpair - Added steps to unpair key fob using UI for Intel vehicles.

Week Ending August 31, 2024

The following new procedure(s) were added:
  1. Media Control Unit (Remove and Replace) - This procedure uses Toolbox to replace the MCU.
  2. Wheel Disposal (Rework)
The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a step to clean the wiper blades.
  2. Wheel (Remove and Replace) - Added instruction for wheel disposal.

Week Ending August 24, 2024

The following new procedure(s) were added:
  1. Door Assembly - Rear Lower LH (Retrofit)
The following procedure(s) were updated:
  1. Adaptive Air Spring Module - Rear - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  2. Air Spring Module - Front - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  3. Air Spring Module - Front - RH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  4. Air Spring Module - Rear - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  5. Air Spring Module - Rear - RH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  6. Door Assembly - Rear Lower - LH (Remove and Replace) - Added information on required retrofit when fitting a 2021+ Model X door to a 2015-2020 Model X.
  7. HV Battery (AWD) (Remove and Install) - Added note stating it is not necessary to perform HV disablement.
  8. HV Battery (AWD) (Remove and Replace) - Added note stating it is not necessary to perform HV disablement.

Week Ending August 17, 2024

The following procedure(s) were updated:
  1. Adaptive Air Spring Module - Front - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
  2. HV/LV Ancillary Unit (HV Battery 2.0) (Remove and Replace) - Added Pack Contactor Replacement routine for vehicles with Tegra MCU.
  3. Seat Assembly - 1st Row - LH (Remove and Replace) - Removed step for running PROC_BCREAR_X_SEAT-INSTALL-MODE-OFFvia Toolbox: (link).
  4. Seat Assembly - 1st Row - RH (Remove and Replace) - Removed step for running PROC_BCREAR_X_SEAT-INSTALL-MODE-OFFvia Toolbox: (link).

Week Ending August 10, 2024

The following new procedure(s) were added:
  1. Air Dryer - Tesla Air Suspension (Regenerate)
The following procedure(s) were updated:
  1. Vehicle Sanitation - Evaporator - Tunap 994 (EMEA) - Removed sub-procedures for sanitation using Tunap 589 and Tunap I880.
  2. Vehicle Sanitation - Interior Air - Tunap 589 (EMEA) - Removed sub-procedures for sanitation using Tunap 996 and Tunap I880.

Week Ending August 3, 2024

The following procedure(s) were updated:
  1. HV/LV Ancillary Unit (HV Battery 2.0) (Remove and Replace) - Swapped illustrations in steps for Hioki measurement on positive and negative terminals.

Week Ending July 27, 2024

The following procedure(s) were updated:
  1. Contactors - HV Battery (HV Battery 1.0/1.5) (Remove and Replace) - Changed tool part number from 1046409-00-B – TIP, CONTACTOR-BUSBAR, L-SHAPED to 1046409-00-A – TIP, CONTACTOR-BUSBAR, L-SHAPED, REV 02.
  2. Fuse Locations - Update the link of Electrical Information.
  3. Sensor - Ride Height - Front - LH (Remove and Replace) - Added note on front sensor mounting bracket.
  4. Sensor - Ride Height - Rear - LH (Remove and Replace) - Added note on rear sensor mounting bracket.

Week Ending July 20, 2024

The following procedure(s) were updated:
  1. Contactors - HV Battery (HV Battery 1.0/1.5) (Remove and Replace) - Added tool info for 1046409-00-B – TIP, CONTACTOR-BUSBAR, L-SHAPED.

Week Ending July 13, 2024

The following new procedure(s) were added:
  1. Assembly - Switches/Harness - Steering Wheel (Remove and Replace)
The following procedure(s) were updated:
  1. BMS PCBA - High Voltage Battery Assembly (HV Battery 2.0) (Remove & Replace) - Swapped illustrations in steps for Hioki measurement on positive and negative terminals, added torque figure to Installtion step 1 for BMS PCBA board.
  2. Front Door Drive Unit - LH (Remove and Replace) - Added instructions to seal the front door drive unit before installing the unit to the vehicle.

Week Ending July 6, 2024

The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated tool part numbers.