Release Notes October-December 2022
Archived Release Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending December 24, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Added vehicle electrical isolation check to procedure.
- Links - Fore - Lower - Front - LH/RH (Remove and Replace) - Delete the Pressurize/Depressurize step.
- Toolbox 3 (Connect and Disconnect) - Added information on Toolbox Proxy.
Week Ending December 17, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Door Mirror Assembly - LH (Remove and Replace) - Procedure revised.
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - All new procedure.
- GUID-161B8CE2-869D-49A0-8506-082D4EC1D545.html - Procedure revised.
Week Ending December 10, 2022
The following procedure(s) were updated:
- Rear Halfshaft Assembly - Small Drive Unit - LH (Remove and Replace) - Procedure improved.
- Seat Assembly - 1st Row - LH (Remove and Install) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - LH (Remove and Replace) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - RH (Remove and Replace) - Updated references from Front Passenger to 1st row RH.
- Subframe Assembly - Front - 1st Generation (Remove and Install) - Clarify that the removed nyloc nuts are to be discarded.
Week Ending December 3, 2022
The following procedure(s) were updated:
- Light - Fog/Reverse - Rear - LH (Remove and Replace) - Updated to the latest validation.
- Light - Map - Front (Remove and Replace) - Updated title and correction code
Week Ending November 19, 2022
The following new procedure(s) were added:
Week Ending November 12, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Carrier - Sensor - Ultrasonic - Rear Door - LH (Remove and Replace) - Added step to use the force gauge for a specified time.
- Charge Port (Remove and Replace) - Added steps to unlock the Gateway.
- Drive Unit - Rear - Large (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Drive Unit - Rear - Small (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- ECE Charge Port Assembly (Remove and Replace) - Added steps to unlock the Gateway.
- Harness - Main Front (Remove & Replace) - Updated step to remove A/C machine hoses.
- Key Fob - Program - Updated programming steps for Tegra vehicles.
- Module - Rear Door Electromechanical Controller - LH (Remove and Replace) - Update correction code from 11365002 to 11335022
- Module - Rear Door Electromechanical Controller - RH (Remove and Replace) - Update correction code from 11366002 to 11336022
- Power Strut - Liftgate (Remove and Replace) - Update title and changed correction code from 11335002 to 11334202
- Calibration - Front Radar Sensor - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
Week Ending November 5, 2022
The following procedure(s) were updated:
- Air Suspension - Pressurize/Depressurize - Full System - Updated topic with Toolbox 3 routines for Tesla Air Suspension.
- Air Suspension - Pressurize/Depressurize - One Air Spring - Replaced Toolbox 2 routines by Toolbox 3 routines.
Week Ending October 29, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Applique - Spine - Center (Remove and Replace) - Updated information on the ultrasonic sensor roof test.
- Charge Port (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Door - Charge Port (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- ECE Charge Port Assembly (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Four Wheel Alignment Check and Adjust - Added torque specification for cam bolt 1608802-00-C
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated Toolbox 3 instructions.
- Halfshaft - Front Drive Unit - LH (1st Generation) (Remove and Replace) - Updated part number for axle remover cable kit.
- Halfshaft - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Updated part number for axle remover cable kit.
- Link - Aft - Lower - LH (Remove and Replace) - Added torque specification for cam bolt 1608802-00-C
Week Ending October 15, 2022
The following procedure(s) were updated:
- Door Assembly - Rear Lower - LH (Remove and Replace) - Added use of Jig, Ultrasonic Sensor Install, MX to install LH rear door ultrasonic sensor carrier.
- Drive Unit - Front (2nd Generation) (Remove and Install) - Added steps to remove front drive unit ground strap, and to perform software reinstall, if new drive unit installed.
- Drive Unit - Front (2nd Generation) (Remove and Replace) - Added note to perform software reinstall after connecting 12V power.
- Drive Unit - Rear - Large (Remove and Replace) - For vehicles outside of NA, added information on the Toolbox 3 immobilizer reset routine.
- Key Fob - Unpair - Corrected Toolbox 2 procedure for Tegra MCUs.
Week Ending October 8, 2022
The following procedure(s) were updated:
- Carrier - Sensor - Ultrasonic - Rear Door - LH (Remove and Replace) - Added jig for ultrasonic sensor carrier alignment.
- Control Arm - Upper - Front - LH (Remove and Replace) - Added tool for installation procedure.
- Control Arm - Upper - Front - RH (Remove and Replace) - Added tool for installation procedure.
- Remove Stuck Deadfront - Charge Handle - Added first step to de-energize the Wall Connector or UMC, and step to put on PPE.