Release Notes July-September 2023

Archived Release Notes:

Week Ending September 30, 2023

The following procedure(s) were updated:
  1. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Install) - Updated to retain the fuse cover bolts and fuse mounting bolts.
  2. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Updated to retain the fuse cover bolts and fuse mounting bolts.
  3. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Install) - Updated to retain the fuse cover bolts and fuse mounting bolts.
  4. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated to retain the fuse cover bolts and fuse mounting bolts.

Week Ending September 23, 2023

The following new procedure(s) were added:
  1. Cover - Pyrotechnic Fuse - HV Battery 1.0/1.5 (Inspect)
  2. Cover - Pyrotechnic Fuse - HV Battery 2.0 (Inspect)
The following procedure(s) were updated:
  1. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Install) - Updated title and HV insulating glove information.
  2. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Updated title and HV insulating glove information.
  3. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Install) - Updated title and HV insulating glove information.
  4. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated title and HV insulating glove information.
  5. Intermediate Shaft - Steering Column - Lower (Remove and Replace) - Replace the steps of removing HEPA filter, wiper motor and reservoir with releasing the wheel arch liner and turning the steering wheel to improve the efficiency.
  6. Toe Link Assembly - Rear - LH (Remove and Replace) - Updated steps to the latest from Service Development.

Week Ending September 16, 2023

The following new procedure(s) were added:
  1. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Install)
  2. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Install)
The following procedure(s) were updated:
  1. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Made consistent with fuse Remove and Install procedure.
  2. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Removed step to perform the vehicle electrical isolation procedure, and made consistent with fuse Remove and Install procedure.
  3. Line - Air Suspension (Repair) - Added part information.
  4. Links - Front Suspension - Lower - Fore and Aft - LH/RH (Remove & Replace) - Added more detailed instructions on cutting the cam bolt. Added the Oscillating Multi-Tool with a carbide teeth blade as an alternative to the cut-off tool when the cam bolt must be cut.
  5. Panel Alignment Specifications - Redirected the information on panel alignment specifications to a new location.

Week Ending September 9, 2023

The following procedure(s) were updated:
  1. Battery - Auxiliary - 12V (Remove and Replace) - Updated the procedure according to the latest input.
  2. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Updated pyrotechnic fuse matrix with Tesladex info, and removed voltage check at fuse.
  3. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated pyrotechnic fuse matrix with Tesladex info, and removed voltage check at fuse.

Week Ending September 2, 2023

The following new procedure(s) were added:
  1. Panel Alignment Specifications
  2. Rear Door Alignment
  3. Puddle Light - Liftgate (Remove & Replace)
  4. Task Light - Footwell Cover - LH (Remove & Replace)
The following procedure(s) were updated:
  1. Charge Port (Remove and Replace) - Moved LV disconnect and charge port voltage check so that they are performed after the trunk side trim is removed.
  2. Charge Port Voltage Check - Made procedures consistent across vehicle lines.
  3. ECE Charge Port Assembly (Remove and Replace) -
  4. Trim - Rear Trunk - Side - LH (Remove and Replace) - Noted for 2nd generation that the 3rd row seatback may be moved up and down as needed in order to access the trunk side panels/brackets.

Week Ending August 26, 2023

The following procedure(s) were updated:
  1. Evaporator (Remove and Replace) - Revised procedure using the latest vehicle validation.
  2. Module - Restraint Control - RCM (Remove and Replace) - Added additional warning to make sure LV is disconnected.

Week Ending August 19, 2023

The following procedure(s) were updated:
  1. All procedures in which chemicals containing diisocyanates are used: added a note on training and certification (EMEA only)
  2. Brake Caliper - Rear - Mando - LH (Remove and Replace) - Updated EPB Service Mode routine.
  3. Brake Pad Kit - Rear - Mando (Remove and Replace) - Updated EPB Service Mode routine.

Week Ending August 12, 2023

The following procedure(s) were updated:
  1. Steering Rack (LHD) (3rd Generation) (Remove and Replace) - Reorganized the procedure.

Week Ending August 5, 2023

The following new procedure(s) were added:
  1. Line - Air Suspension (Repair)
The following procedure(s) were updated:
  1. Key Fob - Program - Updated Tegra and Intel Program sections to latest validation.
  2. Service Mode - Added video and deleted information for older firmware version.

Week Ending July, 29, 2023

The following procedure(s) were updated:
  1. Drive Unit - Rear - Large (Remove and Replace) - Added Note about security-related toolbox actions.
  2. Drive Unit - Rear - Small (Remove and Replace) - Added Note about security-related toolbox actions.
  3. Key Fob - Program - Added Note about security-related toolbox actions.

Week Ending July 22, 2023

The following new procedure(s) were added:
  1. Harness - Center Console (Remove and Replace)
The following procedure(s) were updated:
  1. Air Suspension - Pressurize/Depressurize - One Air Spring - Improved procedure.
  2. Air Suspension - Pressurize/Depressurize - Full System - Updated procedure and Toolbox 3 routines.
  3. Four Wheel Alignment Check - Removed unnecessary steps.
  4. Four Wheel Alignment Check and Adjust - Added Service Mode instructions.
  5. Headlights (Adjust), Europe (ECE) - Corrected metric to inch conversion for applying tape to wall.
  6. Ride Height - Adjust - Added note to height cycle calibration step.
  7. Sensor - Ultrasonic - Rear Door - LH (Remove and Replace) - Updated procedure to latest GSD validation, elevated temperature and pressure values for ultrasonic sensor installation.
  8. Link - Aft - Lower - LH (Remove and Replace) - Added the Oscillating Multi-Tool with a carbide teeth blade as an alternative to the cut-off tool when the cam bolt must be cut.
  9. Retractor - Seatbelt - 2nd Row - LH (Bench Seat) (Remove and Replace) - Updated fastener torque spec for LH bench seat installation.
  10. Removed steps for replacing flexible brake hose, and added steps for releasing brake hose from the caliper and replacing washers during install.

Week Ending July 15, 2023

The following new procedure(s) were added:
  1. Large Drive Unit Inverter Isolation Check
The following procedure(s) were updated:
  1. Module - Body Controller - BCM (Remove and Replace) - Updated links.
  2. Steering Rack (LHD) (1st Generation) (Remove and Replace) - Updated post-replacement routines.
  3. Steering Rack (LHD) (2nd Generation) (Remove and Replace) - Updated post-replacement routines.
  4. Steering Rack (RHD) (1st Generation) (Remove and Replace) - Updated post-replacement routines.
  5. Steering Rack (RHD) (2nd Generation) (Remove and Replace) - Updated post-replacement routines.

Week Ending July 8, 2023

The following new procedure(s) were added:
  1. Horn - Tone - Pair (Remove and Replace)
The following procedure(s) were updated:
  1. Horn - High Tone (Remove and Replace) - This procedure is merged to Horn - Tone - Pair (Remove and Replace).
  2. Horn - Low Tone (Remove and Replace) - This procedure is merged to Horn - Tone - Pair (Remove and Replace).