13/08/2024 22:58:41

Link - Panoramic Roof - 1st Generation - Rear - LH (Remove and Replace)

Correction code 24106902

Remove

  1. Remove the sliding glass. See Sliding Glass - Panoramic Roof Assembly (Remove and Replace).
  2. Remove LH floor mat.
  3. Remove the LH IP side cover. See Assembly - Instrument Panel Side Cover - LH (Remove and Replace).
  4. Remove the LH middle A pillar panel. See Panel - A Pillar Trim - Middle - LH (Remove and Replace).
  5. Remove LH sill panel trim. See Trim - Sill Panel - LH (Remove and Replace).
  6. Remove the driver's side lower trim dash. SeeTrim - Dash - Driver's Side - Lower (Remove and Replace).
  7. Remove driver's footwell cover assembly. See Assembly - Cover - Footwell - Driver's (Remove and Replace).
  8. Disconnect premium amplifier if equipped.
    Informational PurposesAn informational icon, calling your attention
    Note
    Applies only to vehicle equipped with premium audio.
  9. Remove OBD II connector from tuner bracket.
  10. Disconnect the connectors(x3) and release the edge clip tuner and move harness for clearance.
  11. Remove bolts (x3) securing tuner bracket to IP.
  12. Remove the amp/tuner bracket assembly out through the bottom of IP carrier.
    Informational PurposesAn informational icon, calling your attention
    Note
    There's a tab on the bracket that requires sliding assembly forward slightly to release.
  13. Remove the 1st generation panoramic roof side applique. See Side Applique - Panoramic Roof - 1st Generation - LH (Remove and Replace).
  14. Remove LH sunroof motor fasteners (x3) and discard.
  15. Use plastic trim tool to separate LH sunroof motor from motor block.
  16. Disconnect LH sunroof motor connector.
  17. Remove the screws (x2) that attach the left rear camera block to vehicle and then removethe rear camera block.
  18. Use a long bit to move panoramic roof rear left link forward to camera block opening.
  19. Lift up rear left link and remove guide shoe.
  20. Slide panoramic roof rear left link back past frame channel.
  21. Remove the LH rear stop screw.
  22. Remove the LH rear 1st generation panoramic roof link from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the link rearward.
    Informational PurposesAn informational icon, calling your attention
    Note
    You may need to use a big hook to pull it out.
  23. Clean the rail and remove old urethane.
  24. Vacuum any debris from the roof and headliner.

Install

  1. Insert the rear left link into the drive cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not damage the fixed glass seal or side rail. Apply lubrication to ease.
  2. Gently tap the rear left link to move assembly into frame channels.
  3. Use a long bit to move panoramic roof rear left link forward to cam block opening.
  4. Lift up rear left link and install guide shoe.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean guide shoe before installation and install some grease.
  5. Slide panoramic roof rear left link back towards rear opening.
    Informational PurposesAn informational icon, calling your attention
    Note
    Line up paint marks at link and panoramic frame.
  6. Install the screws (x2) that attach the left rear camera block to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    T25, 5 Nm.
  7. Install the LH rear stop screw.
  8. Slide panoramic roof front left link back
    Informational PurposesAn informational icon, calling your attention
    Note
    Line up paint marks at link and panoramic frame.
  9. Connect LH sunroof motor connector.
  10. Position the LH sunroof motor onto the motor block, and then install new bolts (x3) for LH sunroof motor to motor block.
    Informational PurposesAn informational icon, calling your attention
    Note
    T25, 5 Nm.
  11. Install amp/tuner bracket assembly back into IP.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure tab is above the IP otherwise there will be a large gap near bulkhead.
  12. Install bolts (x3) securing tuner bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    10mm, 6 Nm.
  13. Reconnect tuner connectors (x2) and secure edge clip (x1).
  14. Install the screws (x2) that attache the OBD II male side to bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    T20, 2.3 Nm.
  15. Connect the premium amplifier if equipped.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully seat connector, then engage locking tab.
  16. Install driver's footwell cover assembly. See Assembly - Cover - Footwell - Driver's (Remove and Replace) .
  17. Install the driver's side lower trim dash. SeeTrim - Dash - Driver's Side - Lower (Remove and Replace) .
  18. Install LH sill panel trim. See Trim - Sill Panel - LH (Remove and Replace) .
  19. Install LH floor mat.
  20. Install the LH middle A pillar panel. See Panel - A Pillar Trim - Middle - LH (Remove and Replace).
  21. Install the LH IP side cover. See Assembly - Instrument Panel Side Cover - LH (Remove and Replace).
  22. Install the sliding glass. See Sliding Glass - Panoramic Roof Assembly (Remove and Replace).
  23. Install the 1st generation panoramic roof side applique. See Side Applique - Panoramic Roof - 1st Generation - LH (Remove and Replace).