29/05/2024 18:12:21

Power Strut - Liftgate (Remove and Replace)

Correction Code 11334202

  • 2023-06-26: Added steps to calibrate the liftgate to the closed position.

Removal

  1. Open the liftgate.
  2. Support the liftgate in the open position.
  3. Remove the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  4. Separate the RH rear corner of the headliner from the body. See Headliner (Remove and Install), Headliner - Glass Roof (Remove and Replace), or Headliner - Panoramic Roof (Remove and Install) as appropriate.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not completely remove the headliner.
  5. Disconnect the liftgate power strut electrical harness connector.
  6. Release the grommet that attaches the liftgate power strut electrical harness to the body.
  7. Release the clip that attaches the liftgate power strut lower socket to the body ball mount, and then separate the socket from the ball mount.
  8. Release the clip that attaches the liftgate power strut upper socket to the liftgate ball mount, and then separate the socket from the ball mount.
  9. Remove the power strut from the vehicle.

Installation

  1. Inspect and record the part number revision of the replacement liftgate power strut for a later step in this procedure.
  2. Install the liftgate power strut upper socket to the liftgate ball mount, and then fasten the clip that attaches the socket to the ball mount.
  3. Install the liftgate power strut lower socket to the body ball mount, and then fasten the clip that attaches the socket to the ball mount.
  4. Fasten the grommet that attaches the liftgate power strut electrical harness to the body.
  5. Connect the liftgate power strut electrical harness connector.
  6. Install the RH rear corner of the headliner to the body. See Headliner (Remove and Install), Headliner - Glass Roof (Remove and Replace), or Headliner - Panoramic Roof (Remove and Install) as appropriate.
  7. Install the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  8. Remove the support from the liftgate.
  9. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  10. Unlock the vehicle gateway for diagnostic communication. See Gateway Unlock.
  11. Perform a gateway configuration change. See Gateway Configuration (Display and Change).
    • If the replacement liftgate power strut part number revision is either -A or -B, change the liftgate_strut_type parameter to "Gen 1".
    • If the replacement liftgate power strut part number revision is -C or later, change the liftgate_strut_type parameter to "Gen 2".
  12. In Toolbox 3, click the Actions tab, type "Pektron-VIN-Learn" into the search field, click on PROC_LFT_TRNK_PEKTRON-VIN-LEARNSearch for routine in ToolboxLFT Pektron VIN Learn, click Run, and allow the routine to complete.
  13. Click the Actions tab, type TEST-RESET_LFTSearch for routine in ToolboxReset LFT (Liftgate) controller into the search field, click on TEST-RESET_LFTSearch for routine in ToolboxReset LFT (Liftgate) controller, click Run, and allow the routine to complete.
  14. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  15. Manually close the liftgate, so that it latches secure.
  16. Press and hold the Close Liftgate button for 5 seconds, to calibrate the liftgate to the closed position.
  17. Verify proper operation of the liftgate.