23/01/2023 11:51:17

Coax Cable - Side Repeater - Front - LH (Replace)

Correction Code 17403012

Procedure

  1. Move the vehicle to a 2-post lift, but do not raise it at this time.
  2. Chock the rear wheels, and place the vehicle into Tow Mode.
  3. Remove the rear apron (refer to procedure).
  4. Remove the LH and RH aprons (refer to procedure).
  5. Remove the HEPA filter inlet duct (refer to procedure).
  6. Remove the HEPA filter outlet duct (refer to procedure).
  7. Remove the underhood storage carpet (refer to procedure).
  8. Remove the wiper arms (refer to procedure).
  9. Remove the cowl screen (refer to procedure).
  10. Remove the LH and RH shock tower braces (refer to procedure).
  11. Remove the wiper motor (refer to procedure).
  12. Remove the glove box (refer to procedure).
  13. Remove the RH center console closeout extension (refer to procedure).
  14. Remove the passenger footwell panel (refer to procedure).
  15. Remove the RH sill panel trim (refer to procedure).
  16. Disconnect 12V power. (refer to procedure).
  17. Apply tape to the LH fender around the side repeater.
  18. Identify the LH repeater coax cable in the donor harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    The LH repeater coax cable has a brown single connector at one end and occupies cavity 2 of the brown dual connector at the other end.
  19. Use the pin drag kit to carefully lift and remove the purple locking insert out of the dual connector.
  20. Use the pin drag kit to carefully lift the locking tab of cavity 2 on the dual connector, and at the same time, pull the LH repeater coax cable from the dual connector.
  21. Wrap the length of the LH repeater coax cable with anti-abrasion tape.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not wrap the brown connector or the bare connector with tape.
  22. Remove the nuts (x3) that attach the body electrical harness to the bulkhead, and then pull the harness dust boot away to expose the wires.
  23. Remove the tape attaching the dust boot to the electrical harness.
  24. Insert the bare connector end of the LH repeater coax cable into the narrow end of the dust boot.
  25. Carefully pull approximately 1.5 feet of cable through the boot, and move that length through the opening in the bulkhead.
  26. Fold the passenger carpet rearward to gain access to the body electrical harness.
  27. Locate connector X846 on the lower A-pillar.
  28. Make sure that there is enough slack in the LH repeater coax cable to reach connector X846.
  29. Attach the LH repeater coax cable to the body electrical harness with two cable ties.
  30. Remove excess cable tie length.
  31. Push the tab to release connector X846 from the body electrical harness.
  32. Push the tabs to separate connector X846.
  33. Use the pin drag kit to carefully lift and remove the purple locking insert out of the male side of connector X846.
  34. Use the pin drag kit to carefully lift the locking tab of cavity 2 on connector X846M, and at the same time, pull the old coax cable from the connector.
  35. Insert the LH repeater coax cable into cavity 2 of connector X846M, and then install the purple locking insert into the connector.
  36. Reconnect the male and female halves of connector X846, and then fasten connector X846 to the body electrical harness.
  37. Wrap the bare connector of the old coax cable with tape.
  38. Attach the coax cable to the body electrical harness with a cable tie.
  39. Remove excess cable tie length.
  40. Unfold the passenger carpet forward.
  41. Install the RH sill panel trim (refer to procedure).
  42. Install the passenger footwell panel (refer to procedure).
  43. Install the RH center console closeout extension (refer to procedure).
  44. Install the glove box (refer to procedure).
  45. Apply tape to attach the narrow end of the dust boot to the frunk electrical harness, and then install the dust boot into the bulkhead.
  46. Install the nuts (x3) that attach the body electrical harness to the bulkhead (torque 5 Nm).
  47. Raise the vehicle and remove the LH front wheel (refer to procedure).
  48. Remove the push clips (x5) and nut that attach rear half of the wheel arch liner to the body
  49. Fold the liner forward, and then place the liner between the brake rotor and fascia.
  50. Release the tabs on the LH side repeater, and push the repeater out of the body.
  51. Disconnect the repeater electrical harness from the LH side repeater connectors, and then remove the repeater assembly from the vehicle.
  52. Route the LH repeater coax cable along the frunk electrical harness, along the old coax cable, and out the side repeater hole in the LH fender.
  53. Use cable ties or tape to attach the LH repeater coax cable to the frunk electrical harness and old coax cable for every 150mm to 200mm of cable length.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use edge clips, cable ties, and tape as necessary to prevent the LH repeater coax cable from contacting abrasive surfaces or sharp edges.
  54. Remove excess cable tie length.
  55. Remove the connector from the old coax cable, and attach the old coax cable to the LH repeater light electrical harness with tape.
  56. Connect the LH repeater light connector and LH repeater coax cable connector to the new repeater assembly.
  57. Install the new repeater into the LH fender.
  58. Unfold the wheel arch liner back to its mounting position, and then install the push clips (x5) and nut that attach the liner to the body (torque 6 Nm).
  59. Install the LH front wheel and remove the vehicle from the lift (refer to procedure).
  60. Chock the rear wheels.
  61. Install the wiper motor (refer to procedure).
  62. Install the LH and RH shock tower braces (refer to procedure).
  63. Install the cowl screen (refer to procedure).
  64. Install the wiper arms (refer to procedure).
  65. Connect 12V power and put the vehicle into Park (refer to procedure).
  66. Install the HEPA filter outlet duct (refer to procedure).
  67. Install the HEPA filter inlet duct (refer to procedure).
  68. Install the underhood storage carpet (refer to procedure).
  69. Install the LH and RH aprons (refer to procedure).
  70. Install the rear apron (refer to procedure).
  71. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  72. Unlock the vehicle gateway. See Gateway Unlock.
  73. In Toolbox 3, click Dashboards > Service Tools > DAS Clear Calibration > Clear Calibration Repeaters.
  74. In Toolbox 3, click Dashboards > Service Tools > View DAS Images > Pre-Calibration, and follow the on-screen instructions to capture the image.
  75. Verify that all cameras are functioning correctly.
  76. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).