Correction code 13016302

1. Open both front doors

   

2. Lower both front windows
   Note

   Using master switch on driver's door

   

3. Move RH front seat backward and seat cushion fully upward

   

4. Open hood
   Note

   Using MCU touchscreen > Controls > Frunk Trunk

   

   

5. Remove rear underhood apron
   Note

   8x clips

   

   

6. Remove RH underhood apron
   Note

   9x clips

   

   

7. Remove LH underhood apron
   Note

   9x clips

   

   

8. Release drainage hoses from HEPA filter inlet duct
   Note

   2x hoses

   

   

9. Remove clips securing HEPA filter inlet duct to cowl panel
   Note

   3x push clips

   

10. Remove HEPA filter inlet duct
    Note

    2x clips on HEPA filter

    

    

11. Remove HEPA filter outlet duct from vehicle
    Note

    Lift up, pull towards front of vehicle, then rotate clockwise

    

    

12. Power down vehicle using MCU
    Note

    Controls > E-brake & Power Off > Power off

    

    

13. Disconnect 12V negative terminal and First Responder Loop
    Note

    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components

    

14. Disconnect controller connectors underneath RH front seat
    Note

    5x connectors, 1x harness clip

    

    

15. Remove RH front seat controller
    Note

    3x clips

    

    

    

    

16. Install RH front seat controller
    Note

    3x clips, Install the rear seat controller clip first and then install the front two clips

    

    

    

    

17. Install connectors to RH front seat controller
    Note

    5x connectors, 1x harness clip

    

    

18. Connect First Responder Loop and 12V negative terminal
    Note

    1x nut, 10mm, 5 Nm, 1x connector

    

19. Install HEPA filter outlet duct

    

    

20. Install HEPA filter inlet duct
    Note

    2x tabs, One on each side

    

    

21. Install clips securing HEPA filter inlet duct to cowl panel
    Note

    3x push clips

    

22. Secure drainage hoses to HEPA filter inlet duct
    Note

    2x hoses

    

    

23. Install LH underhood apron
    Note

    9x clips

    

    

24. Install RH underhood apron
    Note

    9x clips

    

    

25. Close hood
    Note

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

26. Move RH front seat to original position

    

27. Close RH front door

    

28. Connect a laptop with Toolbox 3.0 to the vehicle.
29. Redeploy vehicle firmware. See Firmware Reinstall - Toolbox.
30. Place vehicle in service mode with touchscreen
    Note

    Hold Tesla "T" icon at top of center display for four seconds and then type "service" into dialog box

    

    

31. Precondition vehicle to 68F
    Note

    Must be preconditioned for 10 minutes before calibration is performed

    

32. Set RH seat heater to level 1
    Note

    RH front passenger seat must have seat heater turned on to level 1 before any calibration is performed

    

33. Apply foot to brake pedal and hold right turn signal indicator for 10 plus seconds
    Note

    This step is required even when using a tethered Ethernet connection. Routine can be run after the 10 seconds expires, Key fob must be present in vehicle

    

    

34. In Toolbox, select "Actions/Autodiag" tab and search for "seat calibrate"
35. Select PROC_VCSEATP_FRONT-PASS_OCS-CALIBRATEvia Toolbox: (link)via Service Mode: Low Voltage ➜ Seats ➜ Calibrate OCS, click "RUN", and allow routine to complete
    Note

    Make sure "Actions" is selected if not already, Ensure nothing is sitting on the passenger seat, Select "X" at top right of window to close once complete
36. Select PROC_VCSEATP_SEAT-CALIBRATEvia Toolbox: (link), click "RUN", and allow routine to complete
    Note

    Make sure "Actions" is selected if not already, Ensure nothing is sitting on the passenger seat, Select "X" at top right of window to close once complete
37. Disconnect Toolbox from vehicle and install cubby under the MCU
    Note

    1x connector, 2x clips

    

    

38. Exit Service Mode
    Note

    Hold Tesla T icon at top of center display for four seconds and then type "service" into dialog box

    

39. Raise both front windows
    Note

    Using master switch on driver's door

    

40. Close LH front door