11/09/2020 16:31:57

Bushing - Drive Unit - Front (Remove and Replace)

Correction Code 40111302

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
To avoid personal injury, eye protection must be worn when performing this operation.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
To avoid personal injury, safety-toe shoes and cut-resistant gloves are recommended when performing this operation.

The drive unit bushing tool set includes the following parts:

1 Driver
2 Front bushing cup
3 Rear bushing cup
4 Nut bearing assemblies
5 Threaded rod

Bushing Removal, Front Motor Mount

Informational PurposesAn informational icon, calling your attention
Note
The front motor mount only permits removal and installation from 1 side of the mount. Remove and install the bushing only in the direction shown.

  1. Remove the drive unit (refer to procedure).
  2. Use brake cleaner to clean the threaded rod and the nut bearing assemblies.
  3. Use 3M Spray Lube 08878 or equivalent to lubricate the threaded rod and the nut bearing assemblies.
  4. Thread 1 nut bearing assembly onto 1 end of the threaded rod.
  5. Slide the closed end of the front bushing cup onto the other end of the threaded rod.
  6. Slide the other end of the threaded rod through the left side of the front bushing.
  7. Slide the driver onto the other end of the threaded rod so that the side of the driver with the single tapered counterbore faces the bushing and the flat side is angled in line with the side of the drive unit.
    1 Faces bushing
    2 Faces nut bearing assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    A gap between the taper on the bushing driver and the bushing is normal. The bushing compresses as the nut bearing assemblies are tightened.
  8. Thread the second nut bearing assembly onto the other end of the threaded rod until it lightly touches the driver.
  9. Adjust the assembly until the front bushing cup is seated flush against the front motor mount.
  10. Place a ratchet wrench onto each nut bearing assembly.
  11. Alternate rotating the ratchet wrenches to push the driver towards the front bushing cup until the bushing is removed into the bushing cup.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the effort required to rotate the ratchet wrenches is excessive, the tool is misaligned and continued ratcheting could cause damage. Loosen the nut bearing assemblies on the threaded rod, add lubrication to the threaded rod, realign the parts, and begin again.
  12. Remove the tool and the bushing from the front motor mount.
  13. Disassemble the removed tool. Discard the bushing.

Bushing Installation, Front Motor Mount

  1. Use brake cleaner to clean the threaded rod and the nut bearing assemblies.
  2. Use 3M Spray Lube 08878 or equivalent to lubricate the threaded rod and the nut bearing assemblies.
  3. Slide the bushing into the left side of the front motor mount so that the shorter cavities are horizontal on the bushing.
    Tip: Draw a reference line on the bushing prior to installation to aid with orientation.
  4. Thread 1 nut bearing assembly onto 1 end of the threaded rod.
  5. Slide the closed end of the front bushing cup onto the other end of the threaded rod.
  6. Slide the other end of the threaded rod through the right side of the front bushing.
  7. Slide the driver onto the other end of the threaded rod so that the side of the driver with the single tapered counterbore faces the bushing and the flat side is angled in line with the side of the drive unit.
    1 Faces bushing
    2 Faces nut bearing assembly
  8. Thread the second nut bearing assembly onto the other end of the threaded rod until it lightly touches the driver.
  9. Adjust the assembly until the front bushing cup is seated flush against the front motor mount.
  10. Place a ratchet wrench onto each nut bearing assembly.
  11. Alternate rotating the ratchet wrenches to push the driver towards the front bushing cup until the bushing is aligned with the machined face of the motor mount (the bushing is slightly visible from the right side of the front motor mount).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the effort required to rotate the ratchet wrenches is excessive, the tool is misaligned and continued ratcheting could cause damage. Loosen the nut bearing assemblies on the threaded rod, add lubrication to the threaded rod, realign the parts, and begin again.
  12. Remove the tool from the bushing and the front motor mount.
  13. Disassemble the removed tool.
  14. Install the drive unit (refer to procedure).
  15. Check the vehicle wheel alignment, and adjust if necessary. See Four Wheel Alignment Check (Coil Suspension) or Four Wheel Alignment Check (Air Suspension).