17/02/2022 05:16:43

HV Harness - Front Drive Unit to HVJB - 1st Generation (Remove and Replace)

Correction Code 44500802

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Only technicians who have been trained in High Voltage Awareness and have completed all required certification courses (if applicable) are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn any time a high voltage cable is handled. Refer to Tech Note TN-15-92-003, "High Voltage Awareness Care Points" for additional safety information.

Special tools required for this procedure:

Supplier Part Number Description
Tesla 1051629-00-A Cap, Connection, Rosenberger, H4Z001-000/52
Tesla 10794924-00-A Nylon Fish Tape, 25 ft.

Removal

  1. Perform the vehicle electrical isolation procedure. See Vehicle HV Disablement Procedure .
  2. Remove the high voltage junction box (HVJB) cover. See HV Junction Box - Cover - 2nd Generation (Remove and Replace) .
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use a multimeter to check voltages across the HV cables and to ground before continuing this procedure.
  3. Remove the front LH wheel arch liner. See Louver - Wheel Arch Liner - Front - LH (Remove and Replace) .
  4. Remove the bolt that secures the HV harness to the bracket in the front left wheel arch (torque 4 Nm). Release the HV harness from the bracket.
  5. Remove and discard the screws (x4) that secure the B+ and B- HV cables to the front drive unit (torque 7 Nm).
  6. Release any push clips that secure the HV harness to studs on the bulkhead.
  7. Install protective caps over both HV cables to protect the terminals and seals.
  8. Secure the HV cables to the nylon fish tape tool using string or fishing line.
    Informational PurposesAn informational icon, calling your attention
    Note
    The nylon fish tape tool is used to pull and route the new harness through the channel during installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure both HV cables together and slightly staggered to reduce the likelihood of one of them getting caught in the channel.
    Informational PurposesAn informational icon, calling your attention
    Note
    The following image shows the HV cables without the protective caps installed.
  9. Lower the vehicle.
  10. Release the front of the LH C-pillar lower trim panel near the base of the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care not to damage component(s).
  11. Fold the carpet inboard to expose the entrance to the channel that runs along the left rocker panel.
  12. Gently pull the HV harness towards the rear of the vehicle and through the channel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure that the string or fishing line is not accidentally released from the HV cables while pulling the nylon fish tape tool through the channel.
  13. Once the HV harness is all the way through the channel, release the string or fishing line, but do not pull the nylon fish tape tool back through the channel or remove it from the vehicle.
  14. Disconnect the 12V connector from the HVIL switch.
  15. Remove the bolts (x3) that secure the fuse bracket (torque 9 Nm).
  16. Remove the bolt that secures the HV fuse ground to the body (torque 5.5 Nm).
  17. Remove the nuts that secure the B+ and B- HV cables to the HVJB (torque 9 Nm).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to replace the fastener(s) after it is removed. The threaded area has a reusable dry sealant, which looks similar to adhesive patch material.
  18. Pull the front of the harness through the grommet between the seat base and 2nd row cabin.
  19. Remove the HV harness and fuse assembly from the vehicle.

Installation

Installation procedure is the reverse of removal, except for the following:
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Replace all patchbolt(s).
  • Install protective caps over both HV cables to protect the terminals and seals when pulling the harness through the channel.
  • Secure the new HV harness to the nylon fish tape tool using string or fishing line and, from the front LH wheel arch, gently pull the front of the nylon fish tape tool through the channel towards the front of the vehicle and retrieve the HV harness.
  • Apply P-80 emulsion to the cable grommet at the rear entrance to the channel and ensure that grommet is fully seated.
  • Apply P-80 emulsion to the connector seals on the HV cables before securing the HV cables to the drive unit.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not apply P-80 emulsion to the HV terminals.