19/05/2023 17:00:16

Headliner - Panoramic Roof (Remove and Replace)

Correction Code 15202002

  • 2023-05-19: Added headliner shipping bag installation tip.

Removal

Informational PurposesAn informational icon, calling your attention
Note
Newer replacement headliner assemblies might not include an overhead console. If necessary, source a new overhead console, or reuse the old console. Refer to the parts catalog for more information.
  1. Open all four doors
  2. Open Liftgate
  3. Lower all 4 windows
  4. Remove LH IP side cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x connector
  5. Remove LH middle A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  6. Remove LH upper A-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw with washer, 7mm, 2 Nm, 1x connector, 2x locating tabs, 1x clip
  7. Remove RH IP side cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, 1x connector
  8. Remove RH middle A-pillar trim
  9. Remove RH upper A-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, 7mm, 2 Nm, 1x connector
  10. Release clips securing overhead console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Insert tool between headliner and console at rearward edge of console and pivot rear edge down
  11. Disconnect microphone and intrusion sensor connectors and remove overhead console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 2x tabs
  12. Remove cover from outer LH sun visor mount
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care not to damage the sun visor mounting cover
  13. Remove LH sun visor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2.8 Nm, 1x tab, 1x connector if equipped with lighted visors
  14. Remove LH sun visor center support
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T15, 2.5 Nm, Release cover and remove screw
  15. Remove cover from outer RH sun visor mount
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care not to damage the sun visor mounting cover
  16. Remove RH sun visor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2.8 Nm, 1x tab, 1x connector if equipped with lighted visors
  17. Remove RH sun visor center support
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T15, 2.5 Nm, Release cover and remove screw
  18. Remove rear view mirror lower trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x tabs, Pull downward at slight angle
  19. Disconnect the rear view mirror electrical connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  20. Remove rear view mirror
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate mirror to release
  21. Remove the rear cover by pulling down to release the clips
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  22. Disconnect triple cam, cam heater grid and temperature humidity sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  23. Disconnect headliner harness at LH A-pillar and remove harness from guide channel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors
  24. Disconnect headliner harness at RH A-pillar and remove harness from guide channel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  25. Disconnect heated wiper area connector and tape to windshield, if equipped
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  26. Release headliner at front of vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  27. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, The number of clips securing the trim varies depending on vehicle production date, Replace any damaged or missing clips prior to re-installing sill trim
  28. Move LH front seat forward
  29. Release bottom portion of LH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips,Take care not to damage, Release the lower portion for access, Replace any damaged or missing clips
  30. Remove fasteners securing LH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T25, 2 Nm
  31. Remove LH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x plastic clips to body, 2x metal clips to upper B-pillar, Replace any damaged or missing clips, Lift the trim to clear the seat and pre-tensioner
  32. Remove LH upper B-pillar trim and move it aside
    Informational PurposesAn informational icon, calling your attention
    Note
    2x metal clips, 1x tab, First pull the lower part toward inside the vehicle to release clips, once released pull the trim downwards
  33. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, The number of clips securing the trim varies depending on vehicle production date, Replace any damaged or missing clips prior to re-installing sill trim
  34. Move RH front seat forward
  35. Release bottom portion of RH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Take care not to damage, Release the lower portion for access, Replace any damaged or missing clips
  36. Remove fasteners securing RH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T25, 2 Nm
  37. Remove RH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x plastic clips to body, 2x metal clips to upper B-pillar, Replace any damaged or missing clips
  38. Remove RH upper B-pillar trim and move it aside
    Informational PurposesAn informational icon, calling your attention
    Note
    2x metal clips, First pull the lower part toward inside the vehicle to release clips, once released pull the trim downwards
  39. Remove parcel shelf
  40. Remove LH middle C pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm, 4x clips
  41. Remove LH C-pillar upper trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  42. Remove bolt securing headliner and support strap at LH C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 10 Nm
  43. Remove RH middle C pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm
  44. Remove RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  45. Remove bolt securing headliner and support strap at RH C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 10 Nm
  46. Remove middle cross brace trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x plastic clips, 2x metal clips, if equipped with tethers, disconnect the tethers from the trim to allow room to work inside the vehicle
  47. Remove bolts securing center headliner
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm
  48. Release headliner at LH side of vehicle above B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Recommend looking at reflection of clip in roof glass and using pick tool to release
  49. Release headliner at RH side of vehicle above B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Recommend looking at reflection of clip in roof glass and using pick tool to release
  50. Fold 2nd row seatbacks down
  51. Release rear of headliner and lower
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips, 3x velcro strips
  52. Remove headliner from liftgate area
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Headliner will bend, but material will return to shape, Use caution not to fold or crease headliner too heavily, Tilt left side down and right side up, slide the headliner outside

Installation

  1. Install headliner through the liftgate area
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Headliner will bend, but material will return to shape, Use caution not to fold or crease headliner too heavily
    Tip: The headliner shipping bag might be useful as a "third hand" for installation.
    1. Lay the shipping bag flat with the opening toward you.
    2. Use scissors to cut both the top and bottom sides of the bag up the middle, until there is about 12 in (30 cm) left. The bag will look like a pair of pants.
    3. Open the vehicle front/rear (as appropriate) doors, set the bag on the vehicle roof, and then bring the "legs" of the bag through each doorway into the cabin.
    4. Tie the very ends of the legs together to make a very loose loop out of the cabin, over the roof, and back into the cabin. If the loop is too tight, cut a little more up the middle.
    5. Use the loop to support the headliner during installation. If the loop is too loose, tie an additional knot to reduce slack.
  2. Install rear portion of headliner into position and clip into place
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips, 3x velcro strips, Replace any damaged or missing clips
  3. Raise 2nd row seatbacks to upright position
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove seat protection if used
  4. Secure headliner at sides of vehicle above B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  5. Install bolts securing center headliner
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm
  6. Install middle cross brace trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x plastic clips, 2x metal clips, if equipped with tethers, Install the tethers onto the trim
  7. Install bolt securing headliner and support strap at RH C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 10 Nm
  8. Install RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  9. Install RH rear C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm, 4x clips
  10. Install bolt securing headliner and support strap at LH C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 10 Nm
  11. Install LH C-pillar upper trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  12. Install LH rear C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm, 4x clips
  13. Install parcel shelf
  14. Install RH upper B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x metal clips, Ensure locating tab at top of B-pillar is aligned to the opening in the body, Replace any broken or missing clips prior to installation
  15. Install RH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x plastic clips, 2x metal clips, Replace any broken or missing clips prior to installation
  16. Install fasteners securing RH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T25, 2 Nm
  17. Secure bottom portion of RH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Replace any damaged or missing clips
  18. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, The number of clips securing the a pillar sill trim varies depending on vehicle production date, Replace any damaged or missing clips prior to re-installing sill trim
  19. Install LH upper B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x metal clips, Ensure locating tab at top of B-pillar is aligned to the opening in the body, Replace any broken or missing clips prior to installation
  20. Install LH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x plastic clips, 2x metal clips, Replace any broken or missing clips prior to installation
  21. Install fasteners securing LH lower B-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T25, 2 Nm
  22. Secure bottom portion of LH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Replace any damaged or missing clips
  23. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, The number of clips securing the A-pillar sill trim varies depending on vehicle production date, Replace any damaged or missing clips prior to re-installing sill trim
  24. Install front portion of headliner into position and secure clips
    Informational PurposesAn informational icon, calling your attention
    Note
    4x metal clips, 2x plastic clips
  25. Connect triple cam, cam heater grid and temperature humidity sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  26. Install the upper mirror cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Make sure the rear view mirror harness is routed so that it hangs freely on the outside and is not pinched between the cover and glare shield assembly
  27. Install the rear view mirror by turning it counter clockwise till it is secure
  28. Connect rear view mirror connector and tuck harness slack along the arm
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  29. Install the lower rear view mirror cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4 tabs, Slide it back in at an angle to seat tabs
  30. Install LH sun visor center support
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T15, 2.5 Nm, Secure cover
  31. Install LH sun visor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2.8 Nm, 1x connector, if equipped with lighted visors
  32. Install LH sun visor mount cover
  33. Install RH sun visor center support
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T15, 2.5 Nm
  34. Install RH sun visor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2.8 Nm, 1x connector, if equipped with lighted visors
  35. Install RH sun visor mount cover
  36. Position new overhead console assembly and connect
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors
  37. Secure overhead console assembly to headliner
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 2x clips, Align tabs towards front of vehicle, Then pivot rear of console up and secure tabs
  38. Connect headliner harness at RH A-pillar and secure in guide channel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  39. Reconnect headliner harness at LH A-pillar and secure in guide channel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors
  40. Install RH upper A pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw with washer, 7mm, 2 Nm, 1x connector, 2x locating tabs, 1x clip
  41. Install RH middle A-pillar trim
  42. Install RH instrument panel side cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, 1x connector, Replace any damaged or missing clips prior to installation
  43. Install LH upper A pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw with washer, 7mm, 2 Nm, 1x connector, 2x locating tabs, 1x clip
  44. Install LH middle A-pillar trim
  45. Install LH side IP cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x connector
  46. Reposition headliner above LH front and rear primary body seals
  47. Reposition headliner above RH front and rear primary body seals
  48. Return RH front seat to original position
  49. Return LH front seat to original position
    Informational PurposesAn informational icon, calling your attention
    Note
    Utilize driver profile settings to return customer seat settings if saved
  50. Raise all 4 windows
  51. Close all four doors
  52. Close liftgate