07/05/2021 11:55:50

Module - Body Controller - BCM (2nd generation) (RHD) (Remove and Replace)

Correction code 17152702

Removal

  1. Remove the LH and RH front seats, refer to procedure.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not disconnect 12V power until both front seats are mechanically detached from the vehicle floor panel.
  2. Remove the LH console closeout extension, refer to procedure.
  3. Release the clips (x4) that attach the LH instrument panel side cover to the instrument panel, disconnect the electrical connector, and then remove the side cover.
  4. Release the clips (x2) that attach the LH middle A-pillar trim to the vehicle, and then remove LH middle A-pillar trim.
  5. Release the clips (x4) that attach the LH lower A-pillar trim to the vehicle, and then remove LH lower A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of clips that attach the A-pillar trim may vary, depending on vehicle production date. Replace any damaged or missing clips prior to reinstalling the trim.
  6. Release the clips (x2) that attach the LH footwell cover, disconnect the electrical connector, and then remove the LH footwell from the vehicle.
  7. Carefully fold back the front section of carpet at the LH footwell.
  8. Remove the bolts (x3) (torque 4 Nm) that attach the LH footwell harness cover to the vehicle, and then remove the LH footwell harness cover.
  9. Release the barrel clips (x2) and edge clips (x3) that attach the body harness to the bulkhead and the BCM bracket.
  10. Remove the bolts (x3) (torque 8 Nm) that connect the connector bracket and air suspension module to the bulkhead.
    Informational PurposesAn informational icon, calling your attention
    Note
    Move the electrical harness away from the fastener for better access.
  11. Move the air suspension module, main harness, and associated connectors away for access to the BCM connections.
  12. Remove RH console closeout extension, refer to procedure.
  13. Release the clips (x3) that attach the driver's footrest to the footrest dead pedal.
  14. Release the clips (x4) that attach the RH instrument panel side cover to the instrument panel, disconnect the electrical connector, and then remove the side cover.
  15. Release the clips (x2) that attach the RH middle A-pillar trim to the vehicle, and then remove RH middle A-pillar trim.
  16. Release the clips (x4) that attach the RH lower A-pillar trim to the vehicle, and then remove LH lower A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of clips securing the trim may vary, depending on vehicle production date. Replace any damaged or missing clips prior to reinstalling the trim.
  17. Release the push clips (x2) that attach the RH footwell cover to the vehicle, disconnect the electrical connector, and then remove the RH footwell cover from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    You may need to press the accelerator pedal down for additional clearance.
  18. Carefully fold back the front section of the carpet at the RH footwell.
  19. Remove the nuts (x2) (torque 5 Nm) that attach the dead pedal to the bulkhead, and then remove the dead pedal.
  20. Remove the bolt (torque 2.5 Nm) that attaches the LH front of the center console to the instrument panel.
  21. Remove the bolt (torque 2.5 Nm) that attaches the RH front of the center console to the instrument panel.
  22. Disconnect the two USB connectors at the RH front side of the console and release them from the console trim.
  23. Disconnect the two 12V connectors for the center console.
  24. Release the clips (x2) and tabs (x2) that attach the cubby under the MCU, and then remove the cubby.
  25. Remove the screw (torque 2 Nm) that attaches the front of the console to the instrument pannel carrier.
  26. Remove the premium console mat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently pry up from the rear edge to release the mat.
  27. Remove the bolts (x2) (torque 3 Nm) that attach the middle of the console to the body.
  28. Release the clips (x6) that attach the rear panel to the console, disconnect the connectors (x3), and then remove the rear panel from the console.
  29. Remove the bolts (x2) (torque 7 Nm) that attach the rear of the center console to the body.
  30. Lift the rear of the center console upward, pull it backward, and then remove the center console from the vehicle.
  31. Fold back the first row carpet to gain access to the floor ducts.
  32. Remove the two outer floor ducts and the center floor duct.
  33. Release the connectors (x9) from the BCM.
  34. Remove the screws (x4) (torque 1.8 Nm) that attach the BCM to the BCM bracket.
  35. Remove the bolts (x2) (torque 27 Nm) at the bottom center of the cross car beam assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Releasing these bolts allows the cross car beam to move a little outward to provide clearance for removal of the BCM.
  36. Remove the BCM.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the BCM out between the cross car beam towards the rear of the vehicle

Installation

Installation procedure is the reverse of removal, except for the following:
  1. After connecting 12V power, redeploy the firmware, refer to procedure.
  2. After installation is completed, relearn all key fobs, refer to procedure.
  3. Perform an immobilizer reset: select Panels > Security > Immobilizer Reset, and then follow the on-screen instructions.