06/03/2024 04:54:05

Bracket - FDU Motor Mount - Rear - RH (Remove and Replace)

Correction code 10104302 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See to make sure wearing proper PPE when performing the below procedure.

Removal

  1. Open the LH front door and lower the window.
  2. Open the hood.
  3. Prepare to raise the vehicle. See Raise Vehicle - 2 Post Lift.
  4. Remove the lug nut covers from the RH front wheel, and then loosen the lug nuts.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Remove the LH and RH underhood aprons. See Underhood Apron - LH (Remove and Replace).
  7. Remove the inlet HEPA filter duct. See Duct - HEPA Filter - Inlet (Remove and Replace).
  8. Remove the outlet HEPA filter duct. See Duct - HEPA Filter - Outlet (Remove and Replace).
  9. Disconnect 12V power. See Disconnect 12V Power.
  10. Remove the RH front wheel. See Wheel Assembly (Remove and Install).
  11. Remove the RH front wheel arch liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  12. Remove the HV battery. See HV Battery (RWD/AWD) (Remove and Install).
  13. Position the vehicle so that the underhoist stand adjustment arm fits just below the subframe.
    Informational PurposesAn informational icon, calling your attention
    Note
    Keep some clearance to be able to adjust the stand height.
  14. Position the underhoist stand under the vehicle and raise it to support the RH front motor mount.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is recommended to add a block between the stand and the RH motor mount.
  15. Release the harness clip from the body.
  16. Remove the bolt and washer that attach the RH motor mount to the RH rear motor mount bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 21mm. Newer vehicles may have EP20 bolts.
  17. Remove the front lower bolt that attaches the RH rear motor mount bracket to the body.
  18. Remove rear lower bolt that attaches the RH rear motor mount bracket to the body.
  19. Remove the front upper bolt that attaches the RH rear motor mount bracket to the body.
  20. Remove the rear upper bolt that attaches the RH rear motor mount bracket to the body.
  21. Remove the RH rear motor mount bracket from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift mount bracket up and pivot it out of the opening.

Installation

  1. Position the RH rear motor mount bracket onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide bracket down into position.
  2. Hand start all four 13 mm bolts that attach the RH rear motor mount bracket to the body.
  3. Torque the rear upper bolt that attaches the RH rear motor mount bracket to the body (torque 31 Nm).
  4. Torque the front upper bolt that attaches the RH rear motor mount bracket to the body (torque 31 Nm).
  5. Torque the rear lower bolt that attaches the RH rear motor mount bracket to the body (torque 31 Nm).
  6. Torque the front lower bolt that attaches the RH rear motor mount bracket to the body (torque 31 Nm).
  7. Position the alignment shim between the RH motor mount and the RH motor mount bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    You only need to install the fork-style shim in the rear mount as the front mount was not touched during this procedure. Alignment shim is not necessary for Raven models.
  8. Install the 21 mm bolt and washer that attach the RH motor mount to the RH rear motor mount bracket (torque 120 Nm).
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles may have EP20 bolts.
  9. Remove the alignment shim from between the RH motor mount and the RH motor mount bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    The alignment shim is not necessary for Raven models.
  10. Use the alignment shim to check that the mount is properly aligned.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the alignment shim does not slide into place easily, loosen the RH drive unit mount bolt and repeat the torque steps. Alignment shim is not necessary for Raven models.
  11. Install the clip that attaches the harness to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  12. Remove the underhoist stand from underneath the vehicle.
  13. Install the HV battery. See HV Battery (RWD/AWD) (Remove and Install).
  14. Install the RH front wheelhouse liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  15. Install RH front wheel. See Wheel Assembly (Remove and Install).
  16. Connect 12V power. See Disconnect 12V Power.
  17. Install the HEPA filter outlet duct. See Duct - HEPA Filter - Outlet (Remove and Replace).
  18. Install the HEPA filter inlet duct. See Duct - HEPA Filter - Inlet (Remove and Replace).
  19. Install the LH and RH underhood aprons. See Underhood Apron - LH (Remove and Replace).
  20. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  21. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
  22. Raise the LH front window and close the LH front door.