2026-04-30
3rd row substrate - LH (7-Seat) (Remove and Replace)
校正代码
1309010601
1309010602
注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时深入了解 FRT 及其创建方式。
注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅人体工程学注意事项查看安全健康的作业规程。
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
- 2026-01-26: Released new procedure.
-
Open all four doors
-
Lower all four windows
-
Open liftgate
-
Move LH front seat forward
-
Position 60 seat into easy entry mode
注Press shoulder switch and push 60 seat forward to position into easy entry mode
-
Move RH front seat forward
-
Position 40 seat into easy entry mode
注Press shoulder switch and push 40 seat forward to position into easy entry mode
-
Remove 3rd row seat cushion and disconnect harness
注1x connector, Pull LH and RH release lever under 3rd row seat cushion to release seat cushion
-
Remove 3rd row LH seat cushion bolster
注1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster towards front of vehicle to remove
-
Remove bolt securing 3rd row LH seat belt retractor to seat frame assembly
注1x bolt, 11mm, 37 Nm, Discard bolt after removal
-
Remove rear load floor
-
Remove 3rd row LH back panel from LH seatback assembly
注10x clips, 2x guide hooks, Once cover clips are disengaged, slide back panel up and away from 3rd row seat for full removal
-
Remove 3rd row LH headrest
注Depress guide button, Insert pick into guide opening, Lift headrest upwards and remove
-
Remove 3rd row LH adjustment guide from LH headrest closeout panel
注1x tab, Release detent tab at rear of seat, then pry adjustment guide upwards to release from seat
-
Remove 3rd row RH adjustment guide from RH headrest closeout panel
注1x tab, Release detent tab at rear of seat, then pry adjustment guide upwards to release from seat
-
Remove 3rd row LH headrest closeout panel from LH backrest
注Lift upward to remove LH headrest closeout panel
-
Remove 3rd row LH shoulder switch from LH backrest
注2x clips, 1x connector
-
Remove 3rd row LH escutcheon from LH backrest
注2x clips
-
Remove fasteners securing 3rd row LH backrest to LH seatback assembly
注2x fasteners, T25, 2.5 Nm
-
Release clips securing 3rd row LH backrest to LH seatback assembly
注4x clips, Push clips in to remove from frame
-
Remove 3rd row LH backrest from LH seatback assembly
注2x tabs
-
Remove 3rd row LH trim cover from LH back substrate
注26x tabs, Release RH tabs then LH tabs
-
Install 3rd row LH trim cover to LH back substrate
注26x tabs, Install LH tabs then RH tabs
-
Install 3rd row LH backrest to LH seatback assembly
注2x tabs, 4x clips
-
Install fasteners securing 3rd row LH backrest to LH seatback assembly
注2x fasteners, T25, 2.5 Nm
-
Install 3rd row LH escutcheon into LH backrest
注2x clips
-
Install 3rd row LH shoulder switch into LH backrest
注2x clips, 1x connector
-
Install 3rd row LH closeout panel into LH backrest
注2x tabs
-
Install 3rd row RH adjustment guide into LH closeout panel
-
Install 3rd row LH adjustment guide into LH closeout panel
-
Install 3rd row LH headrest
注Depress adjustment guides during installation
-
Install 3rd row LH back panel to LH seatback assembly
注2x tabs, 10x clips
-
Install rear load floor
-
Install bolt securing 3rd row LH seat belt retractor to seat frame assembly
注1x bolt, 11mm, 37 Nm, Bolt is one time use
-
Install 3rd row LH seat cushion bolster
注1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster into seat frame assembly
-
Install 3rd row seat cushion and connect harness
注1x connector, Secure 3rd row seat cushion into RH and LH latches
-
Move 60 seat to original position
-
Move LH front seat to original position
-
Move 40 seat to original position
-
Move RH front seat to original position
-
Raise all four windows
-
Close all four doors
注If LV is powered up, Unlatch rear doors before closing
-
Close liftgate