2026-04-30

ECU - Charge Port (7-Seat) (Remove and Replace)

校正代码 TBD FRT 0.54 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

拆卸

Open all four doors and lower all windows.
Open the hood via the touchscreen.
Move the 1st row LH and RH seats forward.

注
Adjust the seat back to avoid contact with the headliner if needed.
Open the liftgate.
Press the shoulder switch and push the 2nd row seats forward to position the seats into the easy entry mode.
Power off the vehicle from center display

注
On the touchscreen, touch Controls > Safety > Power Off > Power Off.
Remove the HEPA filter. See 滤清器总成 - HEPA ((拆卸和更换)).
Remove the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) ((拆卸和更换)).
Press the front switch at the LH trunk trim panel to release the 3rd row LH seat backrest.
Press the rear switch at the LH trunk trim panel to release the 3rd row RH seat backrest.
Disconnect the LV power. See 低压电源（锂）（断开和连接） (Modify).
Remove the rear load floor.
Remove the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
Remove the LH trunk pocket bracket. See 储物袋支架 - LH（七座）（拆卸和更换）.
Release the remaining clips, and then remove the LH 7s trunk side trim.

注
1x push clip, 2x clip tabs, 4x Guide tabs
Release the LH trunk side trim and disconnect the 12V outlet connector.

注
4x clips, 7x tabs, 1x connector
Disconnect the charge port ECU connectors (x3).
Remove the bolt that attaches the charge port ECU to the vehicle, and then slide the charge port ECU to the right, and then remove the charge port ECU from the vehicle.

注
10mm

安装

Install the charge port ECU by sliding it into the slots (x2) of the vehicle body, and then install the bolt that attaches the charge port ECU to the vehicle.

注
10mm, 9 Nm
Connect the charge port ECU connectors (x3).
Position the LH trunk side trim and install the lower clips.

注
1x push clips, 5x clips,

注
Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly. Guide the front clip stanchions around the LH C-pillar.
Install the LH trunk side trim.

注
7x tabs, 4x clips, 1x location pin, 1x connector

注
Make sure the trunk seal is properly seated against the edge of the trim.
Install the LH trunk pocket bracket. See 储物袋支架 - LH（七座）（拆卸和更换）.
Connect the LV power. See 低压电源（锂）（断开和连接） (Modify).
Install the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) ((拆卸和更换)).
Move the 1st row and 2nd row seats back to their original positions.
Install the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
Raise the 3rd row RH seat backrest to its original position.

注
Manually raise the backrest up to its original position until it locks into place.
Raise the 3rd row LH seat backrest to its original position.

注
Manually raise the backrest up to its original position until it locks into place.
Install the rear load floor.
Close the liftgate.
Reinstall the vehicle firmware. See 软件重新安装 - 触摸屏.
Raise all windows and close all doors.