2026-07-16

Hinge - Liftgate (Model Y Standard) (Remove and Replace)

校正代码 1133050312 FRT 0.66 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-07-06: Released new procedure.

拆卸

  1. Fold 2nd row 60 and 40 seatbacks down.
  2. Partially remove LH trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    注
    9x clips. Only release the upper section of the trim. Be careful to avoid straining the 12V socket harness at the rear of the trim. All clips and datums shown in the image are shown for clarity.
  3. Remove the LH upper C-pillar trim. See GUID-10185070-F789-4960-8DF2-607E08CD4375.html.
  4. Repeat steps 2 and 3 on the RH side of the vehicle.
  5. Partially lower the headliner at the LH rear side.
    Informational PurposesAn informational icon, calling your attention
    注
    4x clips. Put an inflatable air bag between the headliner and the roof of the vehicle. Make sure that the airbag is away from the liftgate hinge bolts.
  6. Apply tape to the LH liftgate hinge location.
    Informational PurposesAn informational icon, calling your attention
    注
    This marks where the hinge should align during installation. Adhesive tape is also attached to the rear body of the hinge to prevent damage to the paint when removing the hinge.
  7. Support the liftgate.
  8. Put an inflatable air bag between the liftgate and the roof glass.
    Informational PurposesAn informational icon, calling your attention
    注
    The airbag is used to prevent the liftgate from directly pressing against the roof glass, causing damage to the roof glass.
  9. Release the LH upper power strut clip from the ball stud at the liftgate.
    Informational PurposesAn informational icon, calling your attention
    注
    Once released, put the power strut down on the door jamb.
  10. Remove the LH liftgate hinge bolts (x2) from the liftgate.
  11. Remove the inner side nut of the LH liftgate hinge.
  12. Apply tape to the LH side liftgate hinge body position
  13. Put a protective mat between the headliner and the roof.
  14. Cut the inner side bolt of the LH liftgate hinge.
    Informational PurposesAn informational icon, calling your attention
    注
    Cut 9 mm upwards from the bottom of the bolt, and do not apply too much force towards the end of the cut.
  15. Remove the outer side nut of the LH liftgate hinge.
  16. Remove the LH liftgate hinge from the body.
    Informational PurposesAn informational icon, calling your attention
    注
    First remove the inner bolt of the hinge from the body. Rotate the hinge clockwise to 30 degrees, then remove the outer bolt of the hinge from the body. Finally, remove the hinge from the body.

安装

  1. Remove the tape from the LH side liftgate hinge body.
    Informational PurposesAn informational icon, calling your attention
    注
    Clean area with IPA wipes if any debris is found.
  2. Remove the old spacers from the body.
    Informational PurposesAn informational icon, calling your attention
    注
    Be careful not to damage the vehicle's painted surfaces.
  3. lnstall the LH liftgate hinge onto the body.
    Informational PurposesAn informational icon, calling your attention
    注
    First, install the outer bolt of the hinge into the body. Then rotate the hinge counterclockwise by 30 degrees to install the inner bolt of the hinge.
  4. Install the nuts that attach the LH hinge hand tight to the body.
    24 Nm (17.7 lbs-ft)
  5. Install the bolts (x2) that attach the LH liftgate hinge to the liftgate hand-tight.
    Informational PurposesAn informational icon, calling your attention
    注
    2x bolts, 13mm, 24 Nm, Torque after later
  6. Install the LH liftgate power strut clip to the ball stud at the liftgate.
    Informational PurposesAn informational icon, calling your attention
    注
    Make sure that the spring clip is properly set.
  7. Remove the inflatable air bag from between the liftgate and the roof glass.
  8. Remove the liftgate support from the vehicle.
  9. Close the liftgate to check gap/flush
    Informational PurposesAn informational icon, calling your attention
    注
    Perform adjustment as necessary to the hinge bolts and trunk striker. Assistance is recommended.
  10. Open the liftgate.
  11. Torque the bolts that attach the LH liftgate hinge to the liftgate.
    24 Nm (17.7 lbs-ft)
  12. Torque the nuts that attach the LH liftgate hinge to the body.
    24 Nm (17.7 lbs-ft)
  13. Apply touch up paint to the fasteners that attach the LH liftgate hinge.
    Informational PurposesAn informational icon, calling your attention
    注
    Make sure to shake touch up paint before applying. Allow 1st coat to dry for 20 minutes before applying a 2nd coat (if necessary).
  14. Install the rear portion of the headliner into position and clip it into place.
    Informational PurposesAn informational icon, calling your attention
    注
    4x clip,s 4x location pins. Seat trunk seal to edge of trim. Replace any broken clips.
  15. Install LH upper C-pillar trim. See GUID-10185070-F789-4960-8DF2-607E08CD4375.html.
  16. Install the LH trunk side trim.
  17. Repeat steps 15 and 16 on the RH side of the vehicle.
  18. Remove the masking tape used for marking the position of the LH liftgate hinge.
  19. Move 2nd row 40 and 60 seatback to the vertical position.