2025-11-03

ECE Headlights - Adjust - Model Y Standard (Tool Method) (Test/Adjust)

校正代码 17409150 0.24 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至ServiceManualFeedback@tesla.com。 注意：请参阅 人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2025-10-23: Released new procedure.

Special tools required for this procedure:

Supplier Part Number Description
Tesla 1133367-00-A Beissbarth Headlight Tester, Model 815

Adjust Headlights using a Headlight Tester

  1. Open the hood.
  2. Enable Service Mode. See 维护模式.
  3. Enter the headlight aiming mode through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    注
    Via Controls > Service > Adjust Headlights.
  4. Enable testdrive override through the touchscreen.
  5. Position the headlight aimer in front of the LH headlight.
    Informational PurposesAn informational icon, calling your attention
    注
    Position the aimer at approx. 30 cm distance from the surface of the headlamp lens, Adjust the height as necessary to match the center point of the headlamp (~78cm). Make sure that the headlight aimer is on a surface, level with the vehicle.
  6. Power on the headlight aimer.
  7. Use the knobs on the base to adjust headlight aimer level.
  8. Align the headlight aimer perpendicular to vehicle.
    Informational PurposesAn informational icon, calling your attention
    注
    Use visor/laser to line up the tester perpendicular to the axis between furthest fender bolts. If the headlight aimer can move between the RH and LH headlights while maintaining the same laser angle projected onto the fender bolts, it is set correctly (perpendicular) to the vehicle.
  9. Initiate the test on the headlight aimer.
    Informational PurposesAn informational icon, calling your attention
    注
    Select Test EC > Free Test.
  10. Set up the headlight aimer.
    • Vehicle: Tesla Y
    • Headlight: LHD - EU Asym, RHD - UK
    • Light: Bi-LED
    • Inclinat.: -1.0 %
    • Height: 78 cm
    Informational PurposesAn informational icon, calling your attention
    注
    Press OK to proceed.
  11. Select OK again to pass fog light settings.
  12. Adjust the headlight aimer to the LH headlight marking.
    Informational PurposesAn informational icon, calling your attention
    注
    Turn on the laser aimer to adjust the tester's horizontal and vertical position to the LH headlamp marking. Markings can be difficult to spot. Use of a piece of paper can aid in finding the center. Turn off the laser aimer before proceeding to the next step.
  13. Start LH headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    注
    Select the LH low beam icon and select the low beam button at the bottom of the screen.
  14. Adjust the LH headlight
    Informational PurposesAn informational icon, calling your attention
    注
    Select Left on the touchscreen, then use the left scroll wheel on the steering wheel to adjust the beam. Target V = -1.0% and H = 0 %. There may be a delay between scroll wheel input and actual light adjustment output. Do not sit in the vehicle as this will affect the headlight height.
  15. Record the results of the headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    注
    Press the "save" icon.
  16. Position the headlight aimer in front of the RH headlight, and then repeat steps 12 to 15 for the RH headlight.
  17. Review the test results of the headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    注
    Select the "Save" icon
  18. Move the headlight aimer away from the vehicle.
  19. Exit headlight adjustment mode from the touchscreen.
  20. Exit Service Mode. See 维护模式.