2023-12-26

Tube - Output - Coolant - Power Conversion System (Remove and Replace)

Correction code 16202202 2.52 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1111868-00-B 커넥터 탈거, 냉각수, PCS, M3
  • 1135762-00-A 키트, 서비스 플러그, 냉각 호스, Model 3
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Remove

  1. 전력 변환 시스템에서 냉각수를 배출합니다. 참조 항목: Ancillary Bay Coolant (Drain and Refill).
  2. 점화식 배터리 차단기를 탈거합니다. Pyrotechnic Battery Disconnect (Remove and Replace)을(를) 참조하십시오.
  3. HV 배터리 음극 컨택터를 탈거합니다. 참조 항목: Contactor - Negative - HV Battery (Remove and Replace).
  4. 흡수 패드 2개를 중간까지 자르고 각 냉각수 배출 튜브 피팅을 패드로 둘러쌉니다.
  5. 냉각수 커넥터 탈거용 도구를 사용하여 튜브 피팅 클립을 전력 변환 시스템의 바브보다 더 넓게 펼칩니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    이 비디오는 전력 변환 시스템으로부터 냉각수 호스를 연결 해제하고 피팅을 연결하는 방법을 보여줍니다.
    그림 1. 냉각수 커넥터 탈거용 도구 사용 예시
  6. 해당 도구 및 튜브 피팅을 함께 당겨서 전력 변환 시스템에서 피팅을 연결 해제합니다.
  7. 배터리 플랜지의 다른 튜브 피팅에 대해서는 5단계~6단계를 반복합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    이전 단계의 비디오를 참조하십시오.
  8. 튜브를 HV 배터리 AC 흡기 하네스에 고정하는 클립을 분리하고 차량에서 튜브를 탈거합니다.
  9. 전력 변환 시스템 및 배터리 플랜지에 플러그를 장착합니다.
  10. 흘린 냉각수를 모두 닦아 냅니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    흘린 냉각수를 통해 전기가 흐를 수 있습니다.

Install

  1. 흘린 냉각수를 모두 닦아 냅니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    흘린 냉각수를 통해 전기가 흐를 수 있습니다.
  2. 튜브를 전력 변환 시스템에 끼우기 전에 O링이 손상되지 않았는지 및 커넥터 그루브에 올바르게 장착되었는지 확인합니다. 필요 시 부품을 교체합니다.

    O링 상태 양호

    O링 상태 불량

  3. Krytox 203 윤활유를 사용하여 냉각수 배출 튜브 O링을 윤활합니다.
  4. 전력 변환 시스템 및 배터리 플랜지에서 플러그를 탈거합니다.
  5. 냉각수 배출 튜브를 전력 변환 시스템과 배터리 플랜지에 장착합니다.
  6. 튜브 피팅을 단단히 눌러 피팅이 확실히 연결되었는지 확인합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    두 클립이 모두 전력 변환 시스템 및 배터리 플랜지에 바브와 완전히 결합되었는지 확인한 다음, 피팅을 당겨서 보존력을 확인합니다.
    그림 2. 확실한 연결의 예시
  7. 냉각수 배출 튜브 피팅 주변에서 흡수제 패드를 제거하고 누출된 냉각수를 닦아냅니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    흘린 냉각수를 통해 전기가 흐를 수 있습니다.
  8. 튜브를 HV 배터리 AC 인입 하네스에 고정하는 클립을 조입니다.
  9. 보조 베이 냉각수 누출 테스트를 수행합니다. 참조 항목: Ancillary Bay Coolant Leak Test.
  10. 12V 보조 배터리 음극 단자만 연결합니다.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    지금은 12V 전력 연결 절차를 따르지 마십시오.
  11. 12V 충전기를 12V 보조 배터리 단자에 연결합니다.
  12. 냉각수를 보충합니다. 참조 항목: Ancillary Bay Coolant (Drain and Refill).
  13. 터치스크린에서 컨트롤 > 안전 및 보안 > 차량 전원 > 전원 끄기를 터치하십시오.
  14. 12V 보조 배터리 단자에서 12V 충전기를 연결 해제합니다.
  15. 12V 보조 배터리 음극 단자를 연결 해제합니다.
  16. HV 배터리 음극 컨택터를 장착합니다. 참조 항목: Contactor - Negative - HV Battery (Remove and Replace).
  17. 점화식 배터리 차단기 고정 지점에서 전압을 측정한 다음 점화식 배터리 차단기를 장착합니다. Pyrotechnic Battery Disconnect (Remove and Replace)을(를) 참조하십시오.