2021-12-26

Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)

Correction code 20101002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.

Torque Specifications

표 1. Torque Specifications: Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
프리텐셔너를 시트 트랙에 고정하는 볼트
40 Nm (29.5 lbs-ft)
  • Torx T50 소켓
  • 3/8인치 표준 래칫
  • 3/8인치 토크 렌치(장착 전용)
  • 3인치 익스텐션
Replace

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. LH 전면 좌석을 맨 앞의 위치로 이동하고 시트를 완전히 들어 올립니다.
  3. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  4. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  5. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 운전석 시트 외측 사이드 실드를 탈거합니다. Side Shield - Outboard - Driver Seat (Remove and Replace)을(를) 참조하십시오.
  7. 커넥터 잠금 장치를 해제한 다음 프리텐셔너에서 전기 커넥터를 연결 해제합니다.
  8. 프리텐셔너를 시트 트랙에 고정하는 볼트를 탈거합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트가 금속 클립으로 프리텐셔너에 고정되어 있습니다. 프리텐셔너 및 볼트는 어셈블리로 교체해야 합니다.
  9. 시트 트랙에서 1열 골반 프리텐셔너를 탈거합니다.

Install

  1. 새 프리텐셔너 및 볼트 어셈블리를 시트 트랙에 장착한 다음 프리텐셔너를 시트 트랙에 고정하는 볼트를 조입니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션
    Informational PurposesAn informational icon, calling your attention
    참고
    프리텐셔너 가이드 핀을 시트 트랙에 정렬합니다.
  2. 프리텐셔너 전기 커넥터를 연결합니다.
  3. 운전석 시트 외측 사이드 실드를 장착합니다. Side Shield - Outboard - Driver Seat (Remove and Replace)을(를) 참조하십시오.
  4. 12V 전원을 다시 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  6. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.