2025-01-17

Bracket - Rear - Center (Remove and Replace)

Correction code 10014302 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Bracket - Rear - Center (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
후면 중앙 브래킷을 차체에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
  • 4인치 익스텐션
재사용

Remove

  1. 후면 페시아를 탈거합니다. 참조 항목: Fascia - Rear (Remove and Install).
  2. 후면 블루투스 패시브 엔트리 모듈에서 전기 배선 하네스 커넥터를 연결 해제합니다.
  3. 볼트를 탈거하고 블루투스 패시브 엔트리 모듈을 차체에 고정하는 클립을 푼 다음 브래킷에서 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • T30 소켓
    • 2인치 익스텐션
  4. 전기 하네스를 후면 중앙 브래킷 어셈블리에 고정하는 클립을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    엔드 클립이 전기 커넥터에 가려져 있습니다.
  5. 후면 중앙 브래킷을 차체에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 4인치 익스텐션
  6. 차량에서 후방 중앙 브래킷을 탈거합니다.

Install

  1. 후면 중앙 브래킷을 차체에 고정하는 볼트를 장착합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 4인치 익스텐션
  2. 후면 중앙 브래킷에 후면 블루투스 패시브 엔트리 안테나 전기 하네스를 고정하는 클립을 장착합니다.
  3. 블루투스 패시브 엔트리 모듈을 차체에 고정하는 볼트를 장착합니다.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • T30 소켓
    • 2인치 익스텐션
  4. 후면 블루투스 패시브 엔트리 모듈에 전기 배선 하네스 커넥터를 연결합니다.
  5. 후면 페시아를 장착합니다. 참조 항목: Fascia - Rear (Remove and Install).