2024-03-18

Raise Vehicle - Floor Jack (Mobile Service)

Correction code 10001105 0.10 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-03-07: Added a warning to stay away from the vehicle before lifting to avoid injury.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 이동식 정비 서비스를 위해 플로어 잭을 사용한 차량 리프팅과 잭 스탠드에 차량을 지지하는 것을 설명합니다. 다른 절차에서 언급하는 경우에만 이 절차를 사용하십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
To reduce the risk of personal injury, use appropriate equipment while performing this operation.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Do not work on an incorrectly supported vehicle.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차의 중요 단계와 확인 사항을 따르지 않으면 심각한 부상 또는 사망에 이를 수 있습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
차량의 손상을 방지하기 위해, 차량의 대각선 지점(예: LH 전면과 RH 후면)에서 동시에 지지하지 마십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
플로어 잭을 사용하기 전에 장비 사용자 매뉴얼에 따라 플로어 잭의 육안 확인을 수행하십시오.

플로어 잭으로 올리기

  1. 차량을 편평한 표면에 주차했는지 확인합니다.
  2. 작업에 필요한 경우가 아니라면, 후드, 트렁크 및 모든 도어가 닫혀 있는지 확인합니다.
  3. 차량을 리프팅할 곳의 대각선 방향의 휠에 휠 굄목을 장착합니다. 예를 들면 다음과 같습니다.
    • 차량의 LH 전면을 리프팅하는 경우: RH 후면 휠에 굄목을 설치합니다.
    • 차량의 RH 전면을 리프팅하는 경우: LH 후면 휠에 굄목을 설치합니다.
    • 차량의 LH 후면을 리프팅하는 경우: RH 전면 휠에 굄목을 설치합니다.
    • 차량의 RH 후면을 리프팅하는 경우: LH 전면 휠에 굄목을 설치합니다.
  4. 플로어 잭 위에 잭 스탠드 어댑터를 배치합니다.
  5. 차량 리프트 지점 아래에 플로어 잭을 배치한 후, 플로어 잭을 조심스럽게 올리면서 잭 스탠드 어댑터 위치 지정 핀을 차량 리프트 지점의 구멍에 정렬합니다.
    그림 1. LH 후면 리프트 지점에서 본 모습, 다른 모서리도 유사함
  6. 차량 아래에 잭 스탠드 간격이 충분해질 때까지 차량을 리프팅한 다음 잭 스탠드 어댑터 아래에 잭 스탠드를 배치합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    If an electric jack or pneumatic jack is used, stay away from the vehicle prior to raising it to avoid injuries.
    Informational PurposesAn informational icon, calling your attention
    참고
    잭 스탠드 컷아웃을 플로어 잭과 정렬합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    잭 스탠드 상단 개구부를 잭 스탠드 어댑터 하단과 정렬합니다.
  7. 플로어 잭을 천천히 낮추면서 잭 스탠드가 잭 스탠드 어댑터와 정렬하는지 확인하십시오.
  8. 작업 영역 밖으로 플로어 잭을 이동합니다.
  9. 동일한 축 또는 차량의 동일한 측면에 또 다른 잭 스탠드를 장착하는 경우, 3-8 단계를 반복합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    손상을 방지하기 위해, 절대로 차량을 대각선 포인트(예: LH 전면과 RH 후면)에서 동시에 지지하지 마십시오

플로어 잭으로 내리기

  1. 차량 아래에 어떠한 공구나 부품도 없는지 확인합니다.
  2. 플로어 잭을 잭 스탠드 아래에 배치한 다음 잭 스탠드에서 차량을 조심스럽게 들어 올립니다.
  3. 차량 아래에서 잭 스탠드를 치웁니다.
  4. 휠이 지면에 닿을 때까지 천천히 차량을 내립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    차량과 일정 거리를 유지하여 부상을 방지하십시오.
  5. 차량 아래에서 플로어 잭을 치웁니다.
  6. 차량에서 휠 굄목을 제거합니다.