24/08/2023 04:43:04

실드 - 차체 컨트롤러 - 전면(히트 펌프)(탈거 및 교체)

교정 코드 17152122 0.18 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

  1. Open LH front door
  2. Lower LH front window
  3. Open hood
    Informational PurposesAn informational icon, calling your attention
    참고
    Press "Open" button on touchscreen to release latch, Lift lid manually
  4. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    참고
    12x clips, Only store rear apron visible face upwards
  5. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  6. Disconnect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    참고
    1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
  7. Disconnect first responder loop
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Release locking tab
  8. Remove vent tube hose from LH side of 12V battery
    Informational PurposesAn informational icon, calling your attention
    참고
    1x tube adapter
  9. Release terminal cover and remove positive terminal
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 1x nut, 10mm, 6 Nm, Do not fully remove positive terminal nut
  10. Remove 12V battery upper tie down strap to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 5 Nm, Lift battery tie down strap up and remove it from rear tie down hook strap
  11. Remove battery upper tie down strap
    Informational PurposesAn informational icon, calling your attention
    참고
    Lift battery tie down strap up and remove it from the rear tie down hook strap
  12. Remove 12V battery from vehicle
  13. Remove rear battery tie down strap
    Informational PurposesAn informational icon, calling your attention
    참고
    Rotate forward to disengage
  14. Disconnect thermal sub-harness from front controller
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Depress locking tab and rotate to release
  15. Remove bolts securing front controller shield assembly and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 8.5 Nm

장착

  1. Install front controller shield to the front controller
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 8.5 Nm
  2. Connect thermal sub-harness to front controller
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Rotate fully to secure locking tab
  3. Install rear battery tie down strap
    Informational PurposesAn informational icon, calling your attention
    참고
    Insert assembly into bracket and rotate to 90 degrees
  4. Install 12V battery into vehicle
  5. Position battery tie down strap onto battery
    Informational PurposesAn informational icon, calling your attention
    참고
    Hook upper tie down strap into rear tie down hook strap and position for installation
  6. Install bolt securing upper tie down strap to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 5 Nm
  7. Install vent tube hose in 12V battery
  8. Install positive terminal and terminal cover
    Informational PurposesAn informational icon, calling your attention
    참고
    1x nut, 10mm, 6 Nm, 2x clips
  9. Connect first responder loop
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
  10. Connect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    참고
    1x nut, 10mm, 6 Nm
  11. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    참고
    12x clips
  12. Close hood
  13. Raise LH front window
  14. Close LH front door