2025-09-23

Horn Assembly (Remove and Replace)

Correction code 17531202 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

    Torque Specifications

    표 1. Torque Specifications: Horn Assembly (Remove and Replace)
    Description Torque Value Recommended Tools Reuse/Replace Notes
    혼 어셈블리를 전면 서브프레임에 고정하는 볼트
    12 Nm (8.8 lbs-ft)
    • 10mm 소켓
    • 6인치 익스텐션
    Reuse 시야 확보를 위해 손전등 권장

    Remove

    그림에서는 LH 전면 휠을 탈거한 모습이 나와 있지만, 실제 절차에는 필요하지 않습니다.
    1. 스티어링 휠을 좌측으로 완전히 돌립니다.
    2. 차량에 LH 전면 휠 아치 라이너의 전면부를 고정하는 클립(7개)을 분리한 후, 휠 아치 라이너를 차량 후면 쪽으로 이동하여 아래의 단계를 수행합니다.
    3. 휠 라이너와 전면 페시아 어셈블리 사이에 팽창식 에어백을 조심스럽게 삽입한 다음 에어백을 팽창시킵니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      이렇게 하면 혼 어셈블리에 접근할 수 있습니다.
    4. 혼 어셈블리를 전면 서브프레임에 고정하는 볼트를 탈거합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      Use of the following tool(s) is recommended:
      • 10mm 소켓
      • 6인치 익스텐션
    5. 혼 어셈블리에서 전기 커넥터(2개)를 연결 해제합니다.
    6. 차량에서 혼 어셈블리를 탈거합니다.

    Install

    1. 혼 어셈블리를 장착을 위해 배치한 다음 전기 커넥터(2개)를 혼 어셈블리에 연결합니다.
    2. 혼 어셈블리를 전면 서브프레임에 고정하는 볼트를 장착합니다.
      12 Nm (8.8 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      참고
      Use of the following tool(s) is recommended:
      • 10mm 소켓
      • 6인치 익스텐션
    3. 휠 라이너와 전면 페시아 사이에 있는 팽창식 에어백의 공기를 빼내 탈거합니다.
    4. LH 전면 휠 아치 라이너의 전면부를 차량에 고정하는 푸시 클립(7개)을 장착합니다.
    5. 스티어링 휠의 중심을 맞춥니다.