2024-01-22

Latch Pin - AC - Charge Port (China) (Remove and Replace)

Correction code 44011132 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-01-12: 절차를 재구성했습니다.
  • 1450424-00-A 미니 래칫 비트 세트
표 1. Torque Specifications: Latch Pin - AC - Charge Port (China) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
액추에이터를 충전 포트 어셈블리에 고정하는 나사(2개)
3.3 Nm (2.4 lbs-ft)
  • 코드리스 래칫/임팩트 드라이버
  • 미니 래칫 비트 세트 - 1450424-00-A
  • 래칫/토크 렌치
Reuse

Remove

  1. 충전 포트(CP)를 탈거합니다. 참조 항목: Charge Port (GB/T Charging Standard) (Remove and Replace).
  2. 수동 해제 케이블을 길게 당겨 액추에이터를 분리합니다.
  3. 액추에이터를 충전 포트 어셈블리에 고정하는 나사(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    최신 차량에는 T20 변조 방지 장치가 장착되어 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 코드리스 래칫/임팩트 드라이버
    • 미니 래칫 비트 세트 - 1450424-00-A
    • 래칫/토크 렌치
  4. 충전 포트 어셈블리에서 액추에이터를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    30도 가량 돌린 다음 액추에이터를 꺼냅니다.
  5. 충전 포트 어셈블리에서 DC 충전 포트 래치 스틱 O링을 탈거하여 폐기합니다.
  6. AC 충전 포트 래치 스틱을 돌려 액추에이터에서 탈거합니다.

Install

  1. 적당한 양의 윤활유를 발라 AC 래치 스틱과 O링을 윤활합니다.
  2. AC 래치 스틱을 돌려 액추에이터에 장착합니다.
  3. DC 래치 스틱 O링을 충전 포트 어셈블리에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    O링을 손상시키지 마십시오.
  4. 액추에이터를 충전 포트 어셈블리에 놓습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    액추에이터를 부드럽게 밉니다. 액추에이터와 충전 포트(CP) 사이에 틈이 없는지 확인합니다.
  5. 액추에이터를 충전 포트 어셈블리에 고정하는 나사(2개)를 장착합니다.
    3.3 Nm (2.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    최신 차량에는 T20 변조 방지 장치가 장착되어 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 코드리스 래칫/임팩트 드라이버
    • 미니 래칫 비트 세트 - 1450424-00-A
    • 래칫/토크 렌치
  6. 충전 포트(CP)를 장착합니다. 참조 항목: Charge Port (GB/T Charging Standard) (Remove and Replace).