2024-04-29

Decor Trim - Cup Holder - Center Console (Remove and Replace)

교정 코드와 FRT

  • Decor Trim - Cup Holder - Center Console (Remove and Replace)용 Model 3: 15190402,0.48
  • Decor Trim - Cup Holder - Center Console (2.0) (Remove and Replace)용 Model 3: 15190412, 0.30

NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove 원래 센터 콘솔용 컵 홀더 장식 트림

  1. 센터 콘솔 하단 후면 패널을 탈거합니다. 참조 항목: Panel - Lower Rear - Center Console (Remove and Replace).
  2. 전면 시트를 가장 낮고 최후방 위치로 옮깁니다.
  3. 후면 언더후드 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  4. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 센터콘솔 후면에서 전기 커넥터를 연결 해제합니다.
  6. 전면 및 후면 센터 콘솔 회전식 덮개를 엽니다.
  7. LH 및 RH 센터 콘솔 장식 트림 및 센터 콘솔 브라이트 스트립을 탈거합니다. 참조 항목: GUID-1DA9E475-B8D2-4553-B060-480EC13DA39F.html.
  8. 컵 홀더 장식 패널을 컵 홀더 어셈블리에 고정하는 클립(6개)을 분리한 다음, 센터 콘솔 어셈블리에서 컵 홀더 장식 패널을 분리합니다.
  9. 보안 차체 컨트롤러 모듈에서 전기 커넥터를 연결 해제한 다음, 차량에서 컵 홀더 장식 패널을 탈거합니다.
  10. 보안 차체 컨트롤러 모듈을 컵 홀더 장식 패널에 고정하는 나사(2개)를 탈거한 다음 패널에서 보안 차체 컨트롤러 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 래칫/토크 렌치
    • Wiha TorqueVario-S 0.80Nm - 2.0Nm
    • Wiha 1/4인치 비트 홀더 어댑터

Remove 센터 콘솔용 컵 홀더 장식 트림(2세대)

  1. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  2. 암레스트를 엽니다.
  3. LH 및 RH 센터 콘솔 장식 트림 및 센터 콘솔 브라이트 스트립을 탈거합니다. 참조 항목: GUID-1DA9E475-B8D2-4553-B060-480EC13DA39F.html.
  4. 컵 홀더 장식 패널을 컵 홀더 어셈블리에 고정하는 클립(6개)을 분리한 다음, 센터 콘솔 어셈블리에서 컵 홀더 장식 패널을 분리합니다.
  5. 보안 차체 컨트롤러 모듈에서 전기 커넥터를 연결 해제한 다음, 차량에서 컵 홀더 장식 패널을 탈거합니다.
  6. 보안 차체 컨트롤러 모듈을 컵 홀더 장식 패널에 고정하는 나사(2개)를 탈거한 다음 패널에서 보안 차체 컨트롤러 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 래칫/토크 렌치
    • Wiha TorqueVario-S 0.80Nm - 2.0Nm
    • Wiha 1/4인치 비트 홀더 어댑터

Install

Installation procedure is the reverse of removal, except for the following:

Informational PurposesAn informational icon, calling your attention
참고
보안 차체 컨트롤러 모듈을 기존 컵 홀더 장식 트림에서 새 컵 홀더 장식 트림으로 옮깁니다.