Headlight - Pair - (Remove and Replace)
Correction code
17400252
0.60
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
헤드라이트를 차체에 고정하는 나사 |
![]() 5.9 Nm (4.4 lbs-ft) |
|
Reuse | |
펜더 브래킷을 차체에 고정하는 볼트 |
![]() 3 Nm (2.2 lbs-ft) |
|
Reuse |
Remove
- 정비 모드를 활성화하십시오. Service Mode을(를) 참조하십시오.
- 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
- 실내 흡기 덕트를 탈거합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
- 후드 래치 커버를 탈거합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
- 후드 내 보관 유닛을 탈거합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
- 전면 페시아를 탈거합니다. Fascia - Front (Remove and Install)을(를) 참조하십시오.
-
LH 헤드라이트에서 전기 커넥터를 연결 해제합니다.
참고커넥터에 빨간색 잠금 탭이 있는 경우: DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
-
펜더 브래킷을 차체에 고정하는 볼트를 탈거한 다음 차량에서 브래킷을 탈거합니다.
TIpUse of the following tool(s) is recommended:
- Torx T20 소켓
-
LH 헤드라이트를 차체에 고정하는 패스너를 탈거합니다.
참고헤드라이트에 하단 패스너가 장착되어 있지 않을 수 있습니다.TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- 차량에서 헤드라이트를 탈거합니다.
- RH 쪽 헤드라이트에 대해 4단계~7단계를 반복합니다.
Install
-
LH 헤드라이트를 차체에 배치합니다.
경고장착하는 중에 헤드라이트를 손상시키지 마십시오.
-
LH 헤드라이트를 차체에 고정하는 패스너를 장착합니다.5.9 Nm (4.4 lbs-ft)참고헤드라이트에 하단 패스너가 장착되어 있지 않을 수 있습니다.TIpUse of the following tool(s) is recommended:
- 10mm 소켓
-
펜더 브래킷을 차체에 고정하는 볼트를 장착합니다.3 Nm (2.2 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T20 소켓
-
LH 헤드라이트의 전기 커넥터를 연결합니다.
- RH 쪽 헤드라이트에 대해 1단계~4단계를 반복합니다.
-
전면 페시아를 장착합니다. Fascia - Front (Remove and Install)을(를) 참조하십시오.
참고전면 페시아 전기 연결부를 연결한 후 절차를 일시 중지하여 소프트웨어 재설치를 시작합니다.
-
이 절차의 나머지 단계와 동시에 소프트웨어 재설치를 수행합니다. Software Reinstall - Touchscreen을(를) 참조하십시오.
참고소프트웨어 재설치를 시작한 후 전면 페시아 장착을 계속합니다.
- 후드 내 보관 유닛을 장착합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
- 후드 래치 커버를 장착합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
- 실내 흡기 덕트를 장착합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
- 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
-
헤드라이트를 조정합니다.
- Headlights - Adjust - EMEA (Tool Method)
- Headlights - Adjust - EMEA (Wall Method)
- Headlights - Adjust - Global (Tool Method)
- Headlights - Adjust - Global (Wall Method)
- Headlights - Adjust - NA (Tool Method)
- Headlights - Adjust - NA (Wall Method)