2024-09-09

Airbag - Driver (Remove and Replace)

Correction code 20010102 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-03-23: 도구를 "소형 일자 드라이버"에서 "밸브 코어 탈거 도구"로 업데이트했습니다.
  • 2023-03-24: 텍스트를 업데이트하고 스티어링 휠 허브 밑면에 구멍 이미지를 추가했습니다.
  • 2023-06-06: 도구 목록에 밸브 코어 탈거 도구를 추가했습니다.
  • 2023-11-09: 밸브 코어 탈거 공구를 올바르게 사용하는 방법에 관한 메모를 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  • 1143985-00-A 밸브 코어 탈거 도구
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
안전보조장치(SRS) 구성품을 올바르게 취급하지 않으면 위험할 수 있습니다. 참조 항목: 에어백 및 안전보조장치(SRS) 사전 주의 사항.

Remove

  1. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  2. 스티어링 휠의 구멍에 밸브 코어 탈거 공구(1143985-00-A)를 충분히 삽입하여 스프링 클립을 동시에 누른 다음 스티어링 휠에서 운전석 에어백을 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    에어백 커넥터 및 배선의 손상을 방지하기 위해, 도구를 구멍 안으로 너무 깊이 삽입하지 마십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸브 코어 탈거 공구를 구멍에 삽입한 다음 공구 핸들을 스티어링 휠을 향해 천천히 들어 올린 다음 계속해서 공구를 집어넣어 래치를 분리합니다.
    그림 1. 구형 차량 - 스티어링 휠 허브 하단 쪽의 구멍
    그림 2. 신형 차량 - 스티어링 휠 허브 밑의 구멍
  3. 스티어링 휠에서 운전석 에어백 전기 커넥터를 연결 해제한 다음 차량에서 에어백을 탈거합니다.

Install

  1. 하단 경적 브래킷이 스티어링 휠에 올바르게 고정되었는지 확인합니다.
  2. 운전석 에어백 전기 커넥터를 스티어링 휠에 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스가 에어백과 경적 사이에 걸리지 않는지 확인합니다.
  3. 스프링 클립으로 에어백을 스티어링 휠에 고정하도록 운전석 에어백을 스티어링 휠에 끝까지 누릅니다.
  4. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  6. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).