2024-09-09

Actuator - Latch - Hood - Secondary (Remove and Replace)

Correction code 11355302 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-04-25: 프렁크 수동 해제 도구에 대한 링크를 수정했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

Informational PurposesAn informational icon, calling your attention
참고
후드 래치가 전자적으로 열리지 않으면 수동 전면 트렁크 도구를 사용하여 후드를 엽니다. TP_1130534-00-A_TOOL FRUNK RELEASE MANUAL MODEL 3를 참조하십시오.
  1. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  2. 실내 흡기 덕트를 탈거합니다. 참조 항목: 덕트 - 상단 - 실내 흡기(탈거 및 교체).
  3. 후드 래치 커버를 탈거합니다. 참조 항목: Cover - Hood Latch (Remove and Replace).
  4. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  5. 후드 래치에서 보조 후드 래치 액추에이터 케이블을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치 암에서 액추에이터 케이블을 탈거하기 전에 클립을 분리합니다.
  6. 보조 후드 래치 액추에이터에서 전기 커넥터를 연결 해제합니다.
  7. 전면 엔드 캐리어에 보조 후드 래치 액추에이터를 고정하는 클립을 풉니다.
  8. 전면 엔드 캐리어에 보조 후드 래치 액추에이터를 고정하는 볼트를 탈거한 다음 차량에서 액추에이터를 탈거합니다.

Install

  1. 전면 엔드 캐리어에 보조 후드 래치 액추에이터를 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
  2. 보조 후드 래치 액추에이터에 전기 커넥터를 연결합니다.
  3. 전면 엔드 캐리어에 보조 후드 래치 액추에이터를 고정하는 클립을 장착합니다.
  4. 후드 래치에 보조 후드 래치 액추에이터 케이블을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치 암에 케이블 끝을 고정시킨 후, 클립을 부착합니다.
  5. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  6. 후드 래치 커버를 장착합니다. 참조 항목: Cover - Hood Latch (Remove and Replace).
  7. 실내 흡기 덕트를 장착합니다. 참조 항목: 덕트 - 상단 - 실내 흡기(탈거 및 교체).
  8. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).