2023-12-01

Frame - Seat Back Rest - Front Passenger's Seat (Remove and Replace)

Correction code 13043502 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. 차량에서 전면 동승석 시트 어셈블리를 탈거합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  2. 전면 동승석 시트 등받이 허리 지지대를 탈거합니다. Lumbar Support - Back Rest - Front Passenger Seat (Remove and Replace)을(를) 참조하십시오.
  3. 플라스틱 절연체를 전면 동승석 시트 프레임에 고정하는 탭을 푼 다음 플라스틱 절연체를 탈거합니다.
  4. 시트 등받이 프레임에서 LH 및 RH 헤드레스트 포스트 가이드를 탈거합니다. Post Guide - Headrest - Front Passenger Seat (Remove and Replace)을(를) 참조하십시오.
  5. 전면 동승석 시트 등받이 리클라이너 모터를 탈거합니다. 참조 항목: Motor - Recliner - Backrest - Driver Seat (Remove and Replace).
  6. LH 및 RH 시트 등받이 프레임을 시트 쿠션 프레임에 고정하는 볼트를 탈거하여 폐기합니다.
    43 Nm (31.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    그림 1. LH를 표시함: RH도 유사함
  7. 프레임을 돌려 쿠션 프레임에서 분리한 다음 등받이 프레임을 위쪽으로 들어 올려 시트 어셈블리에서 탈거합니다.

Install

  1. 장착을 위해 전면 동승석 시트 등받이 프레임을 시트 어셈블리 위에 놓습니다.
  2. LH 및 RH 시트 등받이 프레임을 시트 쿠션 프레임에 고정하는 새 볼트를 장착합니다.
    43 Nm (31.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    그림 2. LH를 표시함: RH도 유사함
  3. 전면 동승석 시트 등받이 리클라이너 모터를 장착합니다. 참조 항목: Motor - Recliner - Backrest - Driver Seat (Remove and Replace).
  4. 시트 등받이 프레임에 LH 및 RH 헤드레스트 포스트 가이드를 장착합니다. Post Guide - Headrest - Front Passenger Seat (Remove and Replace)을(를) 참조하십시오.
  5. 플라스틱 절연체를 전면 동승석 시트 프레임에 고정하는 탭을 장착한 다음 플라스틱 절연체를 탈거합니다.
  6. 전면 동승석 시트 등받이 허리 지지대를 장착합니다. Lumbar Support - Back Rest - Front Passenger Seat (Remove and Replace)을(를) 참조하십시오.
  7. 전면 동승석 시트 어셈블리를 차량에 장착합니다. 참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).