2023-02-23

Switch - Interior Door Release - Front - LH (Remove and Replace)

Correction code 15131602 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. LH 전면 도어 트림 패널을 탈거합니다. Panel - Door Trim - Front - LH (Remove and Replace)을(를) 참조하십시오.
  2. 탭(4개)에서 NVH 패드를 분리한 다음 LH 도어 패널에서 패드를 탈거합니다.
  3. 도어 트림 패널을 조심스럽게 들어 올려 실내 도어 해제 핸들 스위치를 도어 트림 패널에 고정하는 볼트를 탈거합니다.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
      Warning IconA warning icon, calling your attention to a possibly risky situation
      경고
      Pry carefully and do not damage the plastic rivets. Damage to the rivets could compromise the integrity of the door trim panel.
  4. 핀 드래그 키트를 사용하여 실내 도어 해제 스위치 전기 커넥터에서 핀(3개)을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    핀 및 전기 커넥터의 위치를 표시합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    핀 및 플러그를 분리하여 좁은 트림 패널 공간을 통과할 수 있도록 합니다.
  5. 작업 영역 주변에 마스킹 테이프를 부착하여 도어 트림 패널을 보호합니다.
  6. 트림 도구를 사용하여 실내 해제 스위치에서 실내 도어 핸들의 전면부를 분리합니다.
  7. 탭(2개)을 분리한 다음 도어 트림 패널에서 실내 도어 해제 스위치를 탈거합니다.

Install

  1. 핀 드래그 키트를 사용하여 새 커넥터에서 핀을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    핀 및 전기 커넥터의 위치를 표시합니다.
  2. 실내 도어 해제 스위치를 도어 트림 패널에 고정하는 탭(2개)을 장착합니다.
  3. 핀을 커넥터에 고정합니다.
  4. 실내 도어 핸들의 전면부를 실내 해제 스위치에 고정합니다.
  5. 도어 트림 패널을 부드럽게 들어 올려 실내 도어 해제 핸들 스위치를 도어 트림 패널에 고정하는 볼트를 장착합니다.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Pry carefully and do not damage the plastic rivets. Damage to the rivets could compromise the integrity of the door trim panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Replace the door trim panel if the plastic rivets are damaged during service.
  6. NVH 패드를 탭(4개)에 고정한 다음 LH 도어 패널에서 NVH 패드를 장착합니다.
  7. LH 전면 도어 트림 패널을 장착합니다. Panel - Door Trim - Front - LH (Remove and Replace)을(를) 참조하십시오.