2024-10-15

A/C Line - Supermanifold to HVAC (Remove and Replace)

Correction code 18201702 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-09-29: UI 루틴을 업데이트했습니다.
  • 2024-09-12: 냉매 - 회수/재충전 교정 코드를 서비스 방문에 별도 활동으로 추가하는 것에 대한 참고 사항을 추가했습니다.
  • 2024-02-28: 루틴을 업데이트했습니다.
Informational PurposesAn informational icon, calling your attention
참고
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Torque Specifications

표 1. Torque Specifications: A/C Line - Supermanifold to HVAC (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
슈퍼매니폴드-HVAC A/C 라인을 HVAC 어셈블리에 고정하는 볼트
22 Nm (16.2 lbs-ft)
  • 13mm 소켓
  • 6인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
슈퍼매니폴드 및 HVAC A/C 라인을 슈퍼매니폴드에 고정하는 너트
27 Nm (19.9 lbs-ft)
  • 13mm 소켓
  • 6인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  2. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  3. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Thermal > Refrigerant System > Start Thermal Fill Drain (Refrigerant only) > Run을 탭하고 루틴이 완료될 때까지 기다립니다.
  4. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. A/C 냉매를 회수합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  6. 외기 흡기 덕트를 탈거합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  7. 12V/LV 보조 배터리를 탈거합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  8. 슈퍼매니폴드-HVAC A/C 라인을 HVAC 어셈블리에 고정하는 볼트(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  9. 슈퍼매니폴드-HVAC A/C 라인을 슈퍼매니폴드에 고정하는 너트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    이 너트는 슈퍼매니폴드-컴프레서 A/C 라인의 뒤에 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  10. 슈퍼매니폴드-HVAC A/C 라인을 슈퍼매니폴드에서 분리한 다음, A/C 라인을 뒤쪽으로 옮기고 위로 올려 탈거합니다.

Install

  1. 슈퍼매니폴드-HVAC A/C 라인을 슈퍼매니폴드에 배치하고 수퍼매니폴드의 스터드 구멍에 A/C 라인 스터드를 삽입합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    적절한 A/C 오일로 새 씰 와셔를 윤활합니다. A/C 오일 규격은 유액 및 용량을(를) 참조하십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    슈퍼매니폴드 아래에 A/C 라인을 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    슈퍼매니폴드 스터드 구멍을 통해 A/C 라인 스터드를 찾습니다.
  2. 슈퍼매니폴드-HVAC A/C 라인을 슈퍼매니폴드에 고정하는 너트를 장착합니다.
    27 Nm (19.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    이 너트는 슈퍼매니폴드-컴프레서 A/C 라인의 뒤에 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  3. 슈퍼매니폴드-HVAC A/C 라인을 HVAC 어셈블리에 고정하는 볼트(2개)를 장착합니다.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  4. 진공 누출 테스트를 수행하고 A/C 냉매를 보충합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  5. 외기 흡기 덕트를 장착합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  6. 12V/LV 보조 배터리를 장착합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  7. 12V/LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  9. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: .
  10. 터치스크린에서 Service Mode > Thermal > Sensors and Valves > Run Heat Pump Commissioning을 터치하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
  11. Actions > Test Thermal Performance를 탭하고 Run을 선택한 다음 루틴이 완료될 때까지 기다립니다.
  12. Actions > Test HVAC Performance를 탭하고 Run을 선택한 다음 루틴이 완료될 때까지 기다립니다.
  13. 정비 모드를 종료합니다. 참조 항목: Service Mode.