2025-09-11

Motor - Seat Track - Driver Seat (Remove and Replace)

Correction code 13011202 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-11-29: 최신 검증에 따라 절차를 다시 기재하였습니다.
  • 2023-12-07: 최신 검증에 따라 운전석 시트 외측 사이드 커버에 대한 단계를 삭제했습니다.
표 1. Torque Specifications: Motor - Seat Track - Driver Seat (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
운전석 시트 패스너(4개)
33.5 Nm (24.7 lbs-ft)
  • Trox Plus T45 소켓
  • 래칫/토크 렌치
  • 코드리스 래칫/임팩트 드라이버
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Replace 볼트가 패치되어 있음
운전석 시트 트랙 브리지를 시트 쿠션 프레임에 고정하는 볼트(2개)
23 Nm (17.0 lbs-ft)
  • Torx T50 비트 스터비
  • 래칫/토크 렌치
  • 3인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Replace 볼트가 패치되어 있음
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. 모든 도어를 열고 창문을 모두 내립니다.
  2. LH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  3. LH 중간 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. LH 전면 도어 씰의 하단 절반을 분리합니다.
  5. LH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. 클립 프라이툴을 사용하여 LH 전면 시트 하네스를 실 트림 클립(3개)에서 분리합니다.
  7. LH 전면 실내 카펫 아래에서 LH 전면 시트 하네스를 당깁니다.
  8. LH 전면 시트를 앞으로 움직인 다음 LH 전면 시트 후면 패스너(2개)를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  9. LH 전면 시트를 뒤로 움직인 다음 LH 전면 시트 전면 패스너(2개)를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  10. LH 전면 시트를 뒤로 기울입니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    차체 컨트롤러에서 LH 시트 하네스를 연결 해제하지 않아도 됩니다. 시트를 이동시킬 때 주의하십시오. 카펫이 손상되지 않도록 하십시오.
  11. 운전석 시트 트랙 브리지를 시트 쿠션 프레임에 고정하는 볼트(2개)를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 비트 스터비
    • 래칫/토크 렌치
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  12. 클립 프라이툴을 사용하여 시트 트랙 모터에서 하네스 클립을 탈거합니다.
  13. 운전석 시트 트랙 모터 커넥터에서 전기 하네스를 연결 해제합니다.
  14. 외측 트랙을 트랙 모터 브리지에서 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트랙 모터 브리지 탭을 들어 올리고 외측 트랙을 밀어 분리합니다.
  15. 트랙 모터 브리지를 내측 트랙에서 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트랙 모터 브리지 탭을 들어 올리고 트랙 모터 브리지를 밀어 내측 트랙에서 분리합니다.

Install

  1. 트랙 모터 브리지를 내측 시트 트랙에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트랙 모터 케이블에는 정사각형 키가 있으며 내측 트랙과 정렬되어야 합니다. 필요에 따라 케이블을 손으로 돌려 정렬하십시오. 트랙 모터 브리지가 완전하고 단단하게 안착될 때까지 내측 트랙에 밀어 넣으십시오.
  2. 외측 시트 트랙을 트랙 모터 브리지에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트랙 모터 케이블에는 정사각형 키가 있으며 내측 트랙과 정렬되어야 합니다. 필요에 따라 케이블을 손으로 돌려 정렬하십시오. 트랙 모터 브리지가 완전하고 단단하게 안착될 때까지 내측 트랙에 밀어 넣으십시오.
  3. 운전석 시트 트랙 브리지를 시트 쿠션 프레임에 고정하는 새 볼트(2개)를 장착합니다.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 비트 스터비
    • 래칫/토크 렌치
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  4. 운전석 시트 트랙 모터 커넥터에 전기 하네스를 연결합니다.
  5. 시트 트랙 모터에 하네스 클립을 장착합니다.
  6. LH 전면 시트를 다시 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    시트를 이동시킬 때 주의하십시오. 카펫이 손상되지 않도록 하십시오.
  7. LH 전면 실내 카펫 아래에서 LH 전면 시트 하네스를 고정합니다.
  8. LH 전면 시트 하네스를 실 트림 클립(3개)에 장착합니다.
  9. LH 전면 시트를 뒤로 움직인 다음 LH 전면 시트 전면 패스너(2개)를 장착합니다.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  10. LH 전면 시트를 앞으로 움직인 다음 LH 전면 시트 후면 패스너(2개)를 장착합니다.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  11. LH 하단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  12. LH 중간 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  13. LH 계기판 엔드캡을 장착합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  14. 터치스크린에서 차량 정비 > 운전석 시트, 스티어링 및 미러 보정 > 시작을 탭한 다음 루틴이 완료될 때까지 기다립니다.
  15. LH 전면 시트를 원래 위치로 이동합니다.
  16. 모든 창문을 올리고 도어를 모두 닫습니다.