2024-08-16

IP Carrier (LHD) (Remove and Replace)

Correction code 14052102 2.22 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-07-30: 서로 다른 버전의 IP 캐리어의 교체하는 방법에 대한 정보를 추가했습니다.
표 1. Torque Specifications: IP Carrier (LHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 및 RH 창문 성에 제거 덕트를 계기판 캐리어에 고정하는 볼트(2개)
2.3 Nm (1.7 lbs-ft)
  • Torx T20 소켓
  • 2인치 익스텐션
  • 래칫/토크 렌치
Reuse

Remove

  1. 계기판 캐리어를 탈거합니다. 참조 항목: IP Carrier (Remove and Install).
  2. 전면 동승석 에어백을 탈거합니다. 참조 항목: Airbag - Front Passenger (Remove and Install).
  3. LH 및 RH 창문 성에 제거 덕트를 계기판 캐리어에 고정하는 볼트(2개)를 탈거하고 덕트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  4. LH 및 RH 성에 제거 커버를 탈거합니다. 참조 항목: GUID-45447BB4-B5CB-45D8-8793-0DB5A4E4435B.html.
    Informational PurposesAn informational icon, calling your attention
    참고
    LH에 탭 4개, RH에 탭 5개.

Install

  1. 2017년 8월 22일 이전에 제조된 Model 3만 해당: 상단 패드의 NVH 문제를 방지하기 위해 펠트 테이프를 부착해야 하는지 확인하려면 Toolbox 문서 39237을 참조합니다.
  2. 새 계기판 캐리어에 트위터 구멍이 없는 경우 교체용 계기판 캐리어를 장착하기 전에 트위터 커넥터를 하네스에 다시 테이프로 고정해야 합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    트위터를 새로 장착하기 위해 새 계기판 캐리어에 구멍을 뚫지 마십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    기존 트위터 커넥터에 테이프를 다시 부착하지 않으면 NVH 문제가 발생할 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    검은색 테이프를 사용하십시오. 그림에 사용된 노란색 테이프는 설명 목적으로만 사용됩니다.
  3. 새로운 계기판 캐리어에 트위터 구멍이 있고 교체된 계기판 캐리어에 트위터 구멍이 없는 경우, 교체용 계기판 캐리어를 장착하기 전에 트위터 구멍을 덮어야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    부틸 조각을 잘라 구멍을 덮습니다. 부틸 조각이 IP 클립을 덮거나 스피커 둘레에 간섭되지 않는지 확인하십시오.
  4. LH 및 RH 성에 제거 커버를 장착합니다. 참조 항목: GUID-45447BB4-B5CB-45D8-8793-0DB5A4E4435B.html.
    Informational PurposesAn informational icon, calling your attention
    참고
    LH에 탭 4개, RH에 탭 5개.
  5. LH 및 RH 창문 성에 제거 덕트를 계기판 캐리어에 고정하는 볼트(2개)를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  6. 전면 동승석 에어백을 장착합니다. 참조 항목: Airbag - Front Passenger (Remove and Install).
  7. 계기판 캐리어를 장착합니다. 참조 항목: IP Carrier (Remove and Install).