2023-12-26

HV Header - Rear Drive Unit - HV Battery (Remove and Replace)

Correction code 16306302 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1140423-00-B 엑스트랙터, 배터리 HV 헤더, Model 3
  • 1140311-00-A 레버 잠금 장치, HV 커넥터, Model 3
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Remove

  1. 차량 전기 절연 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure.
  2. 후면 HV 배터리 스키드 플레이트를 탈거합니다. 참조 항목: Skid Plate - HV Battery - Rear (Remove and Replace).
  3. RH 내측 HV 배터리 리턴 호스를 HV 배터리에 고정하는 클립을 분리합니다.
  4. 후륜 구동 장치 HV 전기 하네스 브래킷을 HV 배터리에 고정하는 너트를 탈거합니다.
    10 Nm (7.4 lbs-ft)
  5. 릴리즈를 밀어 후륜 구동 장치-HV 배터리 하네스의 HV 배터리 후륜 구동 장치 커넥터 핸들을 고정된 위치에서 잠금 해제합니다.
  6. HV 배터리 후륜 구동 장치 커넥터의 핸들을 완전히 들어 올립니다.
  7. HV 배터리 헤더에서 HV 배터리 후륜 구동 장치 커넥터를 탈거합니다.
  8. HV 헤더를 HV 배터리에 고정하는 볼트를 분리합니다.
  9. 엑스트랙터(extractor) 공구를 HV 헤더에 삽입하고 공구 핸들을 밀어 넣은 다음, 헤더를 당겨 HV 배터리에서 탈거합니다.

Install

  1. HV 헤더를 HV 배터리에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    헤더를 밀고 당겨 헤더가 고정되었는지 확인합니다.
  2. HV 헤더를 HV 배터리에 고정하는 볼트를 장착하여 손으로 조입니다.
  3. 볼트를 적절한 토크로 조입니다.
    10 Nm (7.4 lbs-ft)
  4. 후륜 구동 장치-HV 배터리 하네스의 HV 배터리 후륜 구동 장치 커넥터 핸들을 완전히 들어 올립니다.
  5. HV 커넥터 특수 도구를 HV 배터리 후륜 구동 장치 커넥터에 장착합니다.
  6. 양손을 사용하여 후륜 구동 장치-HV 배터리 하네스의 HV 배터리 후륜 구동 장치 커넥터를 HV 배터리 헤더에 단단히 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    커넥터가 헤더에 정확하고 단단히 체결되었고 고정 핀이 핸들에 삽입되는지 확인하십시오.
  7. HV 배터리 후륜 구동 장치 커넥터에서 HV 커넥터 특수 도구를 탈거합니다.
  8. HV 배터리 후륜 구동 장치 커넥터를 HV 배터리 헤더에 누르는 동안 핸들을 완전히 내립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    핸들이 내려갈 때 고정되지 않게 합니다.
  9. 릴리즈를 밀어 HV 배터리 후륜 구동 장치 커넥터 핸들을 고정 위치에 잠급니다.
  10. HV 배터리 후륜 구동 장치 커넥터가 안착했는지 확인하고, 커넥터 양쪽을 비교하여 제자리에 올바르게 고정되었는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터가 잘못 안착되면 나중에 커넥터 손상 및 후륜 구동 장치 문제가 발생할 수 있습니다.
  11. 후륜 구동 장치 HV 전기 하네스 브래킷을 HV 배터리에 고정하는 너트를 장착합니다.
    10 Nm (7.4 lbs-ft)
  12. RH 내측 HV 배터리 리턴 호스를 HV 배터리에 고정하는 클립을 조입니다.
  13. 후면 HV 배터리 스키드 플레이트를 장착합니다. 참조 항목: Skid Plate - HV Battery - Rear (Remove and Replace).
  14. 보조 베이 공기 누출 테스트를 수행합니다. 참조 항목: Ancillary Bay Air Leak Test.
  15. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).