2024-10-15

Wiper Module (RHD) (Remove and Replace)

Correction code 175096020.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-10-04: 장착 섹션에 소프트웨어 재설치 단계를 추가했습니다.
  • 2023-06-30: 장착 후 와이퍼 교체 절차를 실행하라는 지침이 추가됐습니다.

Remove

  1. 카울 스크린 패널을 탈거합니다. 참조 항목: Panel - Cowl Screen (Remove and Replace) (RHD).
  2. 와이퍼 모듈을 차량에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
  3. 와이퍼 모듈을 차량 전면으로 조심스럽게 당겨 벌크헤드의 브래킷에서 고무 앵커를 분리합니다.
  4. 와이퍼 모듈을 돌린 다음 와이퍼 모듈에서 전기 커넥터를 연결 해제합니다.
  5. 차량에서 와이퍼 모듈을 탈거합니다.

Install

  1. 와이퍼 모듈을 위아래를 뒤집은 상태에서 전기 커넥터를 연결합니다. 그 후 와이퍼 모듈을 차량 뒤쪽으로 돌려 적절한 하네스 간격을 확보합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스를 점검하여 배선이 올바르게 되었는지 확인합니다.
  2. 와이퍼 모듈을 차량 뒤쪽으로 조심스럽게 밀어 고무 앵커가 벌크헤드의 브래킷에 삽입되도록 합니다.
  3. 와이퍼 모듈을 차량에 고정하는 볼트(2개)를 장착합니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
  4. 카울 스크린 패널을 장착합니다. 참조 항목: Panel - Cowl Screen (Remove and Replace) (RHD).
  5. 터치스크린을 통해 정비 모드를 활성화합니다. 참조 항목: Service Mode.
  6. 소프트웨어 재설치를 수행합니다. 참조 항목: Software Reinstall - Touchscreen.
  7. 와이퍼 교체 절차를 실행합니다. 터치스크린에서 정비 > 개폐장치 > 창문 > 와이퍼 교체를 터치하고 실행을 터치한 다음 루틴이 완료될 때까지 기다립니다.
  8. 윈드실드 워셔 및 와이퍼 작동을 확인합니다.