2022-03-08

Actuator - Latch - Hood (Single Actuator System) (Remove and Replace)

Correction code 11350402 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

Informational PurposesAn informational icon, calling your attention
참고
후드 래치가 전자적으로 열리지 않으면 아래에 명시된 수동 전면 트렁크 도구를 사용하여 후드를 엽니다.
  • 1130534-00-A, TOOL, FRUNK RELEASE, MANUAL
  1. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  2. 실내 흡기 덕트를 탈거합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
  3. 후드 래치 커버를 탈거합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  4. 후드 내 보관 유닛을 탈거합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  5. 후드 래치에서 후드 래치 액추에이터 케이블을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치 암에서 액추에이터 케이블을 탈거하기 전에 클립을 분리합니다.
  6. 후드 래치 액추에이터에서 전기 커넥터를 연결 해제합니다.
  7. 전면 엔드 캐리어에 후드 래치 액추에이터를 고정하는 볼트를 탈거한 다음 차량에서 액추에이터를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치

Install

  1. 전면 엔드 캐리어에 후드 래치 액추에이터를 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  2. 후드 래치 액추에이터에 전기 커넥터를 연결합니다.
  3. 후드 래치에 후드 래치 액추에이터 케이블을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치 암에 케이블 끝을 고정시킨 후, 클립을 부착합니다.
  4. 후드 내 보관 유닛을 장착합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  5. 후드 래치 커버를 장착합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  6. 실내 흡기 덕트를 장착합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
  7. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.