2024-09-16

Wheel (Remove and Replace)

교정 코드 34015002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-08-29: 휠 폐기 지침을 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Informational PurposesAn informational icon, calling your attention
참고

탈거

  1. 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  2. 밸브 코어 도구를 사용하여 밸브 코어를 탈거하고 타이어 공기를 배출합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 공기가 빠르게 배출됩니다. 보안경 및 장갑 등 적절한 PPE를 착용합니다.
  3. 휠의 정면이 위를 향하도록 타이어 기계에 놓습니다.
  4. 휠에 중앙 클램프를 배치합니다.
  5. 휠 콘을 중앙 클램프 및 휠에 배치한 다음 콘을 중앙 클램프에 조입니다.
  6. 상단 비드 롤러를 상단 림 가장자리에 배치한 다음 하단 비드를 하단 림 가장자리에 배치합니다.
  7. 휠을 회전하여 타이어 상단 비드와 타이어 하단 비드를 풀어줍니다. 휠이 회전할 때 비드를 윤활합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    TPMS 센서가 림 근처에 있습니다. 상단 비드를 풀 때 TPMS 센서가 손상되지 않도록 합니다.
  8. 타이어 기계 암을 림 가장자리에 배치한 다음 비드 레버를 사용하여 암을 타이어 상단 비드에 걸어줍니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    휠이 회전할 때 암이 TPMS 센서를 손상시키지 않도록 TPMS 센서를 타이어 기계 암보다 앞에 배치합니다.
  9. 휠을 회전하여 타이어 상단 비드를 림 위로 당깁니다. 휠이 회전할 때 비드를 윤활합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 기계 암이 TPMS 센서에 접촉하지 않게 합니다.
  10. 타이어를 들어 올리고 타이어 하단 비드에 대해 이전 2단계를 반복한 다음 타이어를 휠에서 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 기계 암이 TPMS 센서에 접촉하지 않게 합니다.
  11. TPMS 센서를 휠에 고정하는 너트를 탈거한 다음 센서를 휠에서 탈거합니다.
  12. 콘 및 중앙 클램프를 휠에서 탈거한 다음 휠을 타이어 기계에서 탈거합니다.

장착

  1. 새 휠의 정면이 위를 향하도록 타이어 기계에 놓습니다.
  2. 휠에 중앙 클램프를 배치합니다.
  3. 휠 콘을 중앙 클램프 및 휠에 배치한 다음 콘을 중앙 클램프에 조입니다.
  4. TPMS 씰을 검사하고 씰이 손상된 경우 교체합니다.
  5. TPMS 센서를 휠에 배치한 다음 센서를 휠에 고정하는 너트를 장착합니다.
    8 Nm (5.9 lbs-ft)
  6. 양쪽 타이어 비드를 윤활합니다.
  7. 타이어 사이드월 양쪽을 검사하여 휠 관련 적절한 타이어 방향을 확인하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    회전 방향을 가리키는 화살표나 "Outside" 또는 "Side Facing Outward" 등의 글자를 찾습니다.
  8. 타이어를 휠 상단에 배치한 다음 타이어 기계 암을 제자리로 이동하여 타이어 하단 비드를 장착합니다.
  9. 휠을 회전하여 타이어 하단 비드를 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 기계 암이 TPMS 센서에 접촉하지 않게 합니다.
  10. 타이어 기계 암을 제자리로 이동하여 타이어 상단 비드를 장착합니다.
  11. 휠을 회전하여 타이어 상단 비드를 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 기계 암이 TPMS 센서에 접촉하지 않게 합니다.
  12. 규격에 따라 주의하여 타이어에 공기를 주입합니다. 타이어 비드가 휠에 안착됩니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 사이드월에 표시된 공기압을 초과하지 마십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    보안경 및 장갑 등 적절한 PPE를 착용합니다.
  13. 밸브 코어 도구를 사용하여 밸브 코어를 장착합니다.
  14. 콘 및 중앙 클램프를 휠에서 탈거한 다음 휠을 타이어 기계에서 탈거합니다.
  15. 휠 및 타이어의 밸런스를 맞춥니다. 참조 항목: Tire - Front - LH (Balance).

폐기

Informational PurposesAn informational icon, calling your attention
참고
If the wheel was replaced due to damage but is still judged to be reusable from a technical point of view, make sure to properly dispose of the wheel. See 휠 폐기(재작업) and add correction code 34015007 as a separate activity to the Service visit.