2024-10-17

Motor - Seat Track - Front Passenger Seat (Remove and Replace)

Correction code 13013202 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-10-15: Updated post-installation routines.
  • 2023-12-08: Re-write the whole procedure according to the latest validation.
표 1. Torque Specifications: Motor - Seat Track - Front Passenger Seat (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 동승석 시트 패스너(4개)
33.5 Nm (24.7 lbs-ft)
  • Trox Plus T45 소켓
  • 코드리스 래칫/임팩트 드라이버
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Replace 볼트가 패치되어 있음
리프트 모터 어셈블리를 후면 RH 링크에 고정하는 볼트
18 Nm (13.3 lbs-ft)
  • Torx 비트 T45 스터비
  • 래칫/토크 렌치
  • 3인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Replace 볼트가 패치되어 있음
RH 트랙 어셈블리를 RH 전면 시트 쿠션 어셈블리에 고정하는 볼트(2개)
23 Nm (17.0 lbs-ft)
  • Torx T50 비트 스터비
  • 3인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 코드리스 래칫/임팩트 드라이버
Reuse 볼트가 패치되어 있음
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. Open all doors and lower all windows.
  2. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  3. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. Release the bottom half of the RH front door seal.
  5. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. Use a clip prytool to release the RH front seat harness from the sill trim clips (x3).
  7. Pull the RH front seat harness from under the RH front cabin carpet.
  8. Move the RH front seat forward, and then remove and discard the RH front seat rear fasteners (x2).
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  9. Raise the RH front seat cushion to maximum height for access to the HV battery bolts at the RH front footwell and below the RH front seat.
  10. Move the RH front seat backward, and then remove and discard the RH front seat front fasteners (x2).
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  11. Tilt the seat backward to gain access to the underside of the LH front seat.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take care when moving the seat. Ensure the carpet is not damaged.
  12. Remove and discard the bolt that attaches the lift motor assembly to the rear RH link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx 비트 T45 스터비
    • 래칫/토크 렌치
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  13. With assistance, remove the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 비트 스터비
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 코드리스 래칫/임팩트 드라이버
  14. Disconnect the front passenger seat track motor electrical connector.
  15. Use a clip prytool to remove the harness clips (x2) from the RH front seat track motor.
  16. Release the front passenger seat outer track from the track bridge assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pry up on the bridge tack motor tab, and then slide the outer track away to release it.
  17. Release the RH front seat track bridge assembly from the inner seat track.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pry up on the bridge tack motor tab, and then slide the seat track bridge assembly away to release it.

Install

  1. Install the RH front seat outer track onto the track bridge assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    The track motor cable is keyed square and must be aligned with the inner track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  2. Install the track motor bridge to the inner track.
    Informational PurposesAn informational icon, calling your attention
    참고
    The track motor cable is keyed square and must be aligned with the inboard track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  3. Connect the track motor electrical connector.
  4. Install the harness clips (x2) to the RH front seat track motor.
  5. With assistance, install the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 비트 스터비
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 코드리스 래칫/임팩트 드라이버
  6. Install a new bolt that attaches the lift motor assembly to the rear RH link.
    18 Nm (13.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx 비트 T45 스터비
    • 래칫/토크 렌치
    • 3인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  7. Reposition the RH front seat onto the RH front seat risers.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take care when moving the seat. Ensure the carpet is not damaged.
  8. Secure the RH front seat harness under the RH front cabin carpet.
  9. Install the RH front seat harness to the sill trim clips (x3).
  10. Move the RH front seat forward, and then install new RH front seat rear fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  11. Move the RH front seat backward, and then install new RH front seat front fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  12. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  13. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  14. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  15. Install the RH front door seal along the lower A-pillar trim.
  16. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
  17. For NA vehicles only: On the laptop, select the Actions tab, then search for "OCS". Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
    Informational PurposesAn informational icon, calling your attention
    참고
    Verify the seat is clear from any tooling or objects prior to calibration.
  18. On the laptop, select the Actions tab, then search for "Seat calibration". Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
  19. Disconnect Toolbox and remove the laptop from the vehicle.
  20. Disable Service Mode. See Service Mode.
  21. Move the RH front seat to original position.
  22. Raise all windows and close all doors.