2023-12-26

AC Cable - Charge Port to HV Battery (3-Phase) (Remove and Replace)

Correction code 445014020.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1076921-00-B 절연 멀티미터, Fluke 1507(북미)
  • 1108272-00-B 캡, 로직 연결, 인버터, 3DU
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
  • 2023-08-22: 절차를 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

Remove

  1. 트렁크를 엽니다.
  2. 후드를 엽니다.
  3. 충전 포트 도어를 엽니다.
  4. 도어 4개 모두와 모든 창문을 내립니다.
  5. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
    Informational PurposesAn informational icon, calling your attention
    참고
    하위 절차 마지막에 차량 절연 절차를 수행하지 마세요.
  6. 충전 포트 전압 점검 절차를 수행합니다. 참조 항목: Charge Port Voltage Check.
  7. LH 후면 실 패널 트림을 탈거합니다. 참조 항목: Trim - Sill Panel - Rear - LH (Remove and Replace).
  8. 트렁크 가니시를 탈거합니다. 참조 항목: Garnish - Trunk (Remove and Replace).
  9. 트렁크 플로어 트림을 탈거합니다. 참조 항목: Trim - Floor - Trunk (Remove and Replace).
  10. 트렁크 실 트림을 탈거합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  11. LH 트렁크 사이드 트림을 탈거합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  12. 흰색 잠금 탭을 탈거한 다음 충전 포트(CP)에서 로직 커넥터를 연결 해제합니다.
  13. 잠금 탭을 위쪽으로 누른 다음 충전 포트(CP)에서 AC 케이블을 연결 해제합니다.
  14. 빨간색 잠금 탭을 분리하고 검은색 레버를 위쪽으로 돌린 다음 보조 베이 HV 헤더에서 AC 케이블을 연결 해제합니다.
  15. 충전 포트 버스바 및 LH 차체 하네스와 관련하여 AC 케이블의 배선 방식을 기록해 두십시오.
  16. 충전 포트 버스바에 AC 케이블을 고정하는 클립(6개)을 탈거합니다.
  17. 차량에서 AC 케이블을 탈거하고 필요에 따라 차체 하네스 밑으로 케이블을 밀어 넣습니다.

Install

  1. 차량에 AC 케이블을 배치하고 필요에 따라 차체 하네스 밑으로 케이블을 밀어 넣습니다.
  2. 충전 포트 버스바에 AC 케이블을 고정하는 클립(6개)을 장착합니다.
  3. AC 케이블을 보조 베이 HV 헤더에 연결하고 검은색 레버를 아래쪽으로 돌린 다음 빨간색 잠금 탭을 체결합니다.
    그림 1. Pre-Structural Pack 배터리.
    그림 2. Structural Pack 배터리.
  4. 충전 포트에 AC 케이블을 연결한 다음 잠금 탭을 아래로 밉니다.
  5. 충전 포트(CP)에 로직 커넥터를 연결한 다음 흰색 잠금 탭을 장착합니다.
  6. LH 2열 시트 등받이를 접습니다.
  7. LH 트렁크 사이드 트림을 장착합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  8. 트렁크 실 트림을 장착합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  9. 트렁크 플로어 트림을 장착합니다. 참조 항목: Trim - Floor - Trunk (Remove and Replace).
  10. 트렁크 가니시를 장착합니다. 참조 항목: Garnish - Trunk (Remove and Replace).
  11. LH 후면 실 패널 트림을 장착합니다. 참조 항목: Trim - Sill Panel - Rear - LH (Remove and Replace).
  12. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).