Torque Specifications - Battery System

Table 1. 토크 규격: 브래킷 - 스키드 플레이트 - 전면 - HV 배터리(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolt that attaches the FDU (Front Drive Unit) HV harness to the FDU
10 Nm (7.4 lbs-ft)
  • 10mm 소켓
재사용
Table 2. 토크 규격: 전력 변환 시스템(PCS)(탈거 및 장착)
설명 토크 값 권장 공구 재사용/교체 참고
Nuts that attach the positive/negative terminal of the DCDC harness to the positive/negative DCDC passthrough busbar
4.5 Nm (3.3 lbs-ft)
  • 8mm 소켓
  • 4인치 익스텐션
  • 래칫/토크 렌치
재사용
Bolts that attach the power conversion system to the HV battery

6 Bolt Power Conversion System:

6 Nm (4.4 lbs-ft)

5 Bolt Power Conversion System:

18 Nm (13.3 lbs-ft)

  • Insulated tools:
    • 8mm 소켓
    • 10인치 익스텐션
    • 래칫/토크 렌치
재사용 Upon installation, mark each bolt with a paint pen
Table 3. 토크 규격: 컨트롤러 - 고전압(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolts that attach the HVC to the ancillary bay cover
5 Nm (3.7 lbs-ft) +30 deg
  • 외부 Torx E10
재사용
Screws that attach the HVC tray to the ancillary bay
2 Nm (1.5 lbs-ft)
  • Insulated tools:
    • Torx T25 소켓
    • 자석 픽업 도구
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
재사용 Not necessary to remove these fasteners if only removing the HVC
Bolts that attach the HVC tray to the HVC
2 Nm (1.5 lbs-ft)
  • Insulated tools:
    • 외부 Torx E6
재사용
Table 4. 토크 규격: 퓨즈 - 보조 베이(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Nuts that attach the ancillary bay fuse to the RH ancillary bay bus
4.5 Nm (3.3 lbs-ft)
  • Insulated 8mm 소켓
교체 1104458-00-A
Table 5. 토크 규격: 점화식 배터리 차단기(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolts that attach the pyrotechnic battery disconnect to the HV battery
  • Torque bolts to
    15 Nm (11.1 lbs-ft)
  • Reverse bolts by 180°
  • Retorque the bolts to
    5 Nm (3.7 lbs-ft)
  • Torque bolts an additional 60°
  • Insulated tools:
    • 13mm 소켓
교체
Table 6. 토크 규격: 스키드 플레이트 - HV 배터리 - 후면(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolt that attaches the rear skid plate to the lower HV battery
13 Nm (9.6 lbs-ft)
  • 외부 Torx Plus EP10
재사용
Nut that attaches the rear skid plate to the upper HV battery
13 Nm (9.6 lbs-ft)
  • 10mm 소켓
재사용
Upper bolts that attach the rear skid plate to the HV battery
35 Nm (25.8 lbs-ft)
  • 13mm 소켓
재사용
Table 7. 토크 규격: 커버 - 보조 베이(탈거 및 장착)
설명 토크 값 권장 공구 재사용/교체 참고
Bolts that attach the ancillary bay rails to the body and ancillary bay cover
24 Nm (17.7 lbs-ft)
  • 15mm 소켓
  • Torx T40 소켓
재사용
Nut that attaches the positive 12V output cable to the DCDC passthrough
9 Nm (6.6 lbs-ft)
  • 13mm 12 포인트 딥소켓
교체 1523698-00-A
Bolts that attach the ancillary bay cover to the high voltage controller
5 Nm (3.7 lbs-ft) +30 deg
  • 외부 Torx E10
재사용
Bolt attaches the ancillary bay cover to the HV battery
8 Nm (5.9 lbs-ft)
  • 외부 Torx E10 5-Lobe
재사용
Table 8. 토크 규격: 커버 - HV 프로브 - HV 배터리(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolt that attaches the HV probe cover to the ancillary bay cover
6 Nm (4.4 lbs-ft)
  • 외부 Torx E10 5-Lobe
교체
Note
토크로 조인 후 페인트 펜으로 패스너에 표시합니다.
Table 9. 토크 규격: 플래터 인클로저 냉각수(배출 및 보충)
설명 토크 값 권장 공구 재사용/교체 참고
Bolt that attach the lower rear edge of the LH wheel arch liner to the body
5 Nm (3.7 lbs-ft)
  • 클립 프라이툴
  • 10mm 소켓
재사용
Table 10. 토크 규격: PTC Heater Electronics (Retrofit)
설명 토크 값 권장 공구 재사용/교체 참고
Nuts that secure the compressor/PTC fuse
4.5 Nm (3.3 lbs-ft)
  • Insulated 8mm 소켓
교체 1104458-00-A

Nut that secures the HV battery ancillary positive busbar

Nut that attaches the negative AC harness to the negative HV battery DC link busbar

4.5 Nm (3.3 lbs-ft)
  • Insulated 8mm 소켓
재사용
Bolts (x2) that secure the PCS output fuse
4.5 Nm (3.3 lbs-ft)
  • Insulated 8mm 소켓
교체 1115833-00-B
Nuts (x2) that attach the AC negative harness to the transformer
2.5 Nm (1.8 lbs-ft)
  • Insulated 7mm 소켓
재사용
Screw that secures the HV carrier assembly
3 Nm (2.2 lbs-ft)
  • Insulated Torx T25 bit
재사용
Bolts (x2) that secure the HV header to the HV battery
10 Nm (7.4 lbs-ft)
  • SKT, 1/4" DR, EP10, LOW PROFILE
  • 재사용 if disassembled less than three times.
  • 교체 if disassembled more than three times
1095042-00-C
M4 nut and bolt
2.5 Nm (1.8 lbs-ft)
  • Insulated Torx T20 비트
  • Insulated 8mm 소켓
재사용
  • Nut: 1104396-00-A
  • Bolt: 1507080-00-A