2022-10-14

Deadfronts - Pin - Charge Port (NA) (Damaged) (Remove and Replace)

Correction code 44012132 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1552269-00-A 데드 프론트 장착 도구, Model 3
  • 1076921-00-B 절연 멀티미터, Fluke 1507 (북미)
  • 1108272-00-B 캡, 로직 연결, 인버터, 3DU
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 PPE(개인 보호 장비)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

Remove

  1. LH 도어를 열고 모든 창문을 내립니다.
  2. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  3. 2열 하단 시트 쿠션의 RH 탭을 분리하여 차량에서 쿠션의 RH 전면 가장자리를 분리한 다음 12V 캡을 사용하여 하단 쿠션을 받칩니다.
  4. 충전 포트 도어를 엽니다.
  5. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 고전압 장갑, 가죽 외부 장갑 및 기타 고전압 PPE를 착용하고 지침이 있을 때까지 제거하지 마십시오.
  7. 충전 포트 전압 점검 절차를 수행합니다. Charge Port Voltage Check을(를) 참조하십시오.
  8. 4mm0.75 탭의 팁에서 8mm를 측정한 다음 페인트 펜을 사용하여 탭 스레드 주변 링에 표시합니다.
  9. 탭 핸들 또는 탭 렌치에 탭을 고정합니다.
  10. 직각 니들 노즈 플라이어를 사용하여 충전 포트 핀 데드 프론트가 회전하지 않도록 한 다음 탭을 페인트 표시까지 데드 프론트에 끼웁니다.
  11. 탭에서 탭 핸들 또는 탭 렌치를 탈거합니다.
  12. 탭을 배터리 작동식 드릴에 주의하여 끼웁니다.
  13. 충전 포트 핀 데드 프론트를 가볍게 당기고 드릴을 시계 방향으로 돌려 충전 포트 핀 데드 프론트 고정 링을 떼어낸 다음 충전 포트 핀에서 데드 프론트를 탈거합니다.
  14. 탭에서 충전 포트 핀 데드 프론트를 탈거합니다.
  15. 드릴에서 탭을 탈거합니다.
  16. 다른 충전 포트 핀 데드 프론트에 대해 9단계~ 15단계를 반복합니다.
  17. 충전 포트에 파손된 핀 데드프런트 조각 또는 잔해물이 있는지 점검하고 ESD 안전 진공청소기로 충전 포트 어셈블리에서 제거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    일부 조각은 제거하려면 니들 노즈 플라이어, 구부러진 수술용 클램프 또는 포켓 스크루드라이버가 필요할 수 있습니다.

Install

  1. 표시된 대로 새 충전 포트 핀 데드 프론트를 데드 프론트 장착 도구의 핀에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    또는 다음 공구를 사용할 수 있습니다.
    • 3mm 육각 소켓
    • 6인치 익스텐션
  2. 무반동 망치를 사용하여 충전 포트 핀 데드 프론트를 충전 포트 핀에 완전히 안착시킵니다.
  3. 다른 새 충전 포트 핀 데드 프론트에 대해 1단계~2단계를 반복합니다.
  4. 가죽 외부 장갑, 고전압 장갑 및 기타 고전압 PPE를 제거합니다.
  5. 12V 전원을 다시 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  7. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  8. 차량이 정상적으로 충전되는지 확인합니다.