2025-03-14

Glove Box - Without Knee Airbags (Remove and Replace)

Correction code 14051012 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

  1. 필요한 경우 글로브박스에서 고객의 물건을 제거하여 안전하게 보관합니다.
  2. LH 및 RH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  3. LH 및 RH 에어 웨이브 엔드캡을 탈거합니다. 참조 항목: End Cap - Air Wave - LH (Remove and Replace).
  4. RH 중간 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  5. RH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. 동승석 발밑 공간 커버를 탈거합니다. 참조 항목: Cover - Footwell - Passenger (LHD) (Remove and Replace).
  7. 주 계기판 장식 트림을 탈거합니다. 참조 항목: Decor Trim - Instrument Panel - Main (Remove and Replace).
  8. 글로브박스를 엽니다.
  9. 글로브박스를 IP 캐리어에 고정하는 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    하나의 나사가 글로브박스 안에 있을 수 있으며 다음 이미지에서 보이지 않을 수 있습니다.
  10. 글로브박스를 IP 캐리어에 고정하는 클립을 분리합니다.
  11. 글로브박스 솔레노이드 커넥터, 댐퍼 커넥터, 퍼들 라이트 커넥터에서 전기 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전기 커넥터 중 2개는 계기판 하단으로 접근합니다.
  12. 차량에서 글로브박스를 탈거합니다.

Install

  1. 글로브박스를 차량으로 가져온 후 글로브박스 솔레노이드 커넥터, 댐퍼 커넥터, 퍼들 라이트 커넥터에 전기 하네스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전기 커넥터 중 2개는 계기판 하단으로 접근합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    퍼들 램프의 전기 하네스를 연결부의 디바이더 앞쪽으로 통과하게 합니다.
  2. 글로브박스를 설치할 때, 글로브박스 댐퍼 핀을 완전히 안착하여 글로브박스 댐퍼와 부딪히지 않게 합니다.
  3. 글로브박스를 IP 캐리어에 고정하는 클립을 조입니다.
  4. 글로브박스를 IP 캐리어에 고정하는 나사를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
  5. 글로브박스를 닫습니다.
  6. 주 계기판 장식 트림을 장착합니다. 참조 항목: Decor Trim - Instrument Panel - Main (Remove and Replace).
  7. 동승석 발밑 공간 커버를 장착합니다. 참조 항목: Cover - Footwell - Passenger (LHD) (Remove and Replace).
  8. RH 하단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  9. RH 중간 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  10. LH 및 RH 에어 웨이브 엔드캡을 장착합니다. 참조 항목: End Cap - Air Wave - LH (Remove and Replace).
  11. LH 및 RH 계기판 엔드캡을 장착합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  12. 터치스크린을 통해 글로브박스가 정상적으로 열리는지 확인하십시오.
  13. 이전에 탈거했던 경우 고객의 소지품을 글로브박스에 다시 넣습니다.