2019-08-13

Beam - 12V Battery (RWD) (Remove and Replace)

Correction code 17012702 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  2. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  3. 실내 흡기 덕트를 탈거합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
  4. 후드 래치 커버를 탈거합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  5. 후드 내 보관 유닛을 탈거합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  6. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  7. 12V 보조 배터리를 탈거합니다. 12V/LV Battery (Remove and Replace)을(를) 참조하십시오.
  8. 12V 배터리 브래킷을 탈거합니다. Bracket - 12V Battery (RWD) (Remove and Replace)을(를) 참조하십시오.
  9. 냉각수 호스와 전기 하네스를 12V 배터리 브래킷 빔에 고정하는 클립을 분리합니다.
  10. 12V 배터리 브래킷 빔에 전면 컨트롤러를 고정하는 볼트를 탈거합니다.
  11. 12V 배터리 빔을 차체에 고정하는 볼트를 탈거합니다.
  12. 12V 배터리 브래킷 빔을 차량에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    차량에서 쉽게 탈거하기 위해 12V 배터리 브래킷 빔의 방향을 조종합니다.

Install

  1. 12V 배터리 브래킷 빔을 차량에 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빔과 브래킷에 엉키지 않도록 12V 배터리 접지 단자를 멀리 띄워 놓습니다.
  2. 12V 배터리 브래킷 빔을 차체에 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
  3. 12V 배터리 브래킷 빔에 전면 컨트롤러를 고정하는 볼트를 장착합니다.
    10 Nm (7.4 lbs-ft)
  4. 냉각수 호스와 전기 하네스를 12V 배터리 브래킷 빔에 고정하는 클립을 장착합니다.
  5. 12V 배터리 브래킷을 장착합니다. Bracket - 12V Battery (RWD) (Remove and Replace)을(를) 참조하십시오.
  6. 12V 보조 배터리를 장착합니다. 12V/LV Battery (Remove and Replace)을(를) 참조하십시오.
  7. 12V 전원을 다시 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  8. 후드 내 보관 유닛을 장착합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  9. 후드 래치 커버를 장착합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  10. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  11. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.