2023-10-27

Steering Wheel (Remove and Install)

Correction code 32051801 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Steering Wheel (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
스티어링 휠-스티어링 컬럼 볼트
80 Nm (59.0 lbs-ft)
  • 10mm 육각
  • 3/8인치 표준 래칫
  • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
  • 3인치 익스텐션
Replace PN - 1036655-00-A

Remove

  1. 차량의 전륜 휠을 일직선으로 정렬하고 스티어링 휠을 중앙으로 정렬합니다.
  2. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  3. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  4. LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 운전석 에어백을 탈거합니다. 참조 항목: Airbag - Driver (Remove and Replace).
  6. 스티어링 휠 전기 배선 하네스 커넥터를 연결 해제합니다.
  7. 스티어링 휠을 스티어링 컬럼에 고정하는 볼트를 탈거하여 폐기합니다.
    80 Nm (59.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 육각
    • 3/8인치 표준 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
    • 3인치 익스텐션
  8. 스티어링 컬럼에서 스티어링 휠을 탈거합니다.

Install

  1. 스티어링 휠을 차량에 배치한 다음, 스티어링 휠을 스티어링 컬럼에 고정하는 새 볼트를 장착합니다.
    80 Nm (59.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 육각
    • 3/8인치 표준 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
    • 3인치 익스텐션
  2. 스티어링 휠 전기 배선 하네스 커넥터를 연결합니다.
  3. 운전석 에어백을 장착합니다. 참조 항목: Airbag - Driver (Remove and Replace).
  4. LV 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  6. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).