2024-04-08

Antenna - Bluetooth Passive Entry - Rear (Remove and Replace)

Correction code 17451802 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-07-31: 소프트웨어 재설치 단계를 Toolbox 셀프 테스트 단계 전으로 옮겼습니다.

Torque Specifications

표 1. Torque Specifications: Antenna - Bluetooth Passive Entry - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bluetooth 패시브 엔트리 모듈을 차체에 고정하는 볼트
3.5 Nm (2.6 lbs-ft)
  • T30 소켓
  • 2인치 익스텐션
Replace 패치 볼트

Remove

  1. 후면 페시아를 탈거합니다. 참조 항목: Fascia - Rear (Remove and Install).
  2. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  3. 후면 Bluetooth 패시브 엔트리 모듈에서 전기 배선 하네스 커넥터를 연결 해제합니다.
  4. 볼트를 탈거하여 폐기하고 Bluetooth 패시브 엔트리 모듈을 차체에 고정하는 클립을 분리한 다음 브래킷에서 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    브래킷에서 모듈을 분리할 때, 좌측을 돌려 브래킷에서 분리하고 탭을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • T30 소켓
    • 2인치 익스텐션

Install

  1. Bluetooth 패시브 엔트리 모듈을 차체에 고정하는 볼트를 장착합니다.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • T30 소켓
    • 2인치 익스텐션
  2. 후면 Bluetooth 패시브 엔트리 모듈에 전기 배선 하네스 커넥터를 연결합니다.
  3. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  4. Reinstall the vehicle firmware. See Software Reinstall - Touchscreen.
  5. Toolbox에서 자가 테스트 루틴을 수행합니다.
    1. Toolbox 3이 설치된 노트북을 연결합니다.
    2. Actions/Autodiag(작업/자동 진단)를 선택한 다음 "Endpoint(엔드포인트)"를 검색합니다.
    3. TEST-SELF_VCSEC_X_ENDPOINT-COMMvia Toolbox: (link)을(를) 선택한 다음 Run을 클릭하고 루틴이 완료될 때까지 기다립니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      완료되면 창의 X를 클릭하여 창을 닫습니다.
  6. 차량에서 노트북을 연결 해제합니다.
  7. 후면 페시아를 장착합니다. 참조 항목: Fascia - Rear (Remove and Install).