2024-04-08

Hose - Inverter to Heat Exchanger - Front Drive Unit (Heat Pump) (Remove and Replace)

Correction code 18300142 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 차량을 2포스트 리프트에 올리고 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. 외기 흡기 덕트를 탈거합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  4. 후드 래치 커버를 탈거합니다. 참조 항목: Cover - Hood Latch (Remove and Replace).
  5. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  6. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  7. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  8. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  9. 냉각수 배출 용기를 전륜 구동장치의 LH 전면 아래에 배치합니다.
  10. 전륜 구동 장치 인버터 인입 호스를 오일 커플링에 고정하는 스프링 클립을 연결 해제한 다음, 호스 및 오일 커플링에 플러그를 장착합니다.
  11. 냉각수 배출 용기를 전륜 구동 장치의 RH 전면 아래에 배치합니다.
  12. 전륜 구동 장치 인버터 인입 호스를 열교환기에 고정하는 클립을 연결 해제한 다음, 호스 끝 및 열교환기에 플러그를 장착합니다.
  13. 차량을 내립니다.
  14. 인버터-열 교환기 호스를 전륜 구동장치에 고정하는 클립을 탈거한 다음, 차량에서 호스를 탈거합니다. 호스를 폐기하는 경우, 각 호스 끝에서 냉각수 플러그를 탈거합니다.

Install

  1. 인버터-열교환기 호스를 전륜 구동 장치에 배치한 다음, 클립으로 고정합니다.
  2. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  3. 냉각수 배출 용기를 전륜 구동장치의 LH 전면 아래에 배치합니다.
  4. 오일 커플링에서 플러그를 탈거한 다음, 전륜 구동장치 인버터 인입 호스를 오일 커플링에 연결합니다. 스프링 클립으로 호스를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밀고 당기기 테스트를 수행하여 호스가 완전히 체결됐는지 확인합니다.
  5. 냉각수 배출 용기를 전륜 구동 장치의 RH 전면 아래에 배치합니다.
  6. 열 교환기에서 플러그를 탈거한 다음, 전륜 구동장치 인입 호스를 열 교환기에 연결합니다. 스프링 클립으로 호스를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밀고 당기기 테스트를 수행하여 호스가 완전히 체결됐는지 확인합니다.
  7. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  8. 차량을 내립니다.
  9. 냉각수 수위를 검사하고 필요한 경우 보충합니다.
  10. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  11. 후드 래치 커버를 장착합니다. 참조 항목: Cover - Hood Latch (Remove and Replace).
  12. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  13. Toolbox 3.0이 설치된 노트북을 차량에 연결합니다.
  14. Actions/Autodiag(작업/자동 진단) 탭을 클릭하고 Purge(배출)를 검색합니다.
  15. TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    을(를) 클릭한 다음 Run을 클릭합니다. 루틴이 완료될 때까지 기다립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    차량이 주행 상태가 아닌지 확인합니다. 차량을 주행 상태로 두면 이 루틴이 중지됩니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    테스트에 약 10분이 걸립니다. 중지 메시지가 표시되어도 루틴이 계속 실행됩니다. 냉각수 펌프 소리가 들립니다. 냉각수 펌프 속도는 PT 서멀 탭 아래의 Garage에서 모니터링할 수 있습니다. 공회전 속도 = ~1500RPM, 테스트 속도는 3500~6500RPM이고 액추에이터 밸브는 SERIES와 PARALLEL 간에 전환됩니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 속도가 7000RPM으로 유지되면 냉각수 펌프는 에어록인 것 의미합니다. 따라서 이 단계를 다시 수행하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 수위가 냉각수 보틀의 NOM과 MAX 선 사이에 도달하도록 계속해서 냉각수를 추가하고 배출합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    완료되면 창 오른쪽 상단에 있는 ‘X’를 선택하여 닫습니다.
  16. 차량에서 노트북을 연결 해제합니다.
  17. 냉각수 수위를 검사하고 필요한 경우 보충합니다.
  18. 외기 흡기 덕트를 장착합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  19. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).