2025-06-27

Headlight - LH (Remove and Replace)

Correction code 17400102 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

표 1. Torque Specifications: Headlight - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
헤드라이트를 차체에 고정하는 나사
5.9 Nm (4.4 lbs-ft)
  • 10mm 소켓
Reuse
펜더 브래킷을 차체에 고정하는 볼트
3 Nm (2.2 lbs-ft)
  • Torx T20 소켓
Reuse

Remove

  1. 정비 모드를 활성화합니다. 참조 항목: Service Mode.
  2. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  3. 전면 페시아를 탈거합니다. 참조 항목: Fascia - Front (Remove and Install).
  4. LH 헤드라이트에서 전기 커넥터를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터에 빨간색 잠금 탭이 있는 경우: DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  5. 펜더 브래킷을 차체에 고정하는 볼트를 탈거한 다음 차량에서 브래킷을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  6. LH 헤드라이트를 차체에 고정하는 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    헤드라이트에 하단 패스너가 장착되어 있지 않을 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  7. 차량에서 헤드라이트를 탈거합니다.

Install

  1. LH 헤드라이트를 차체에 배치합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    장착하는 중에 헤드라이트를 손상시키지 마십시오.
  2. LH 헤드라이트를 차체에 고정하는 패스너를 장착합니다.
    5.9 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    헤드라이트에 하단 패스너가 장착되어 있지 않을 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  3. 펜더 브래킷을 차체에 고정하는 볼트를 장착합니다.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  4. LH 헤드라이트의 전기 커넥터를 연결합니다.
  5. 전면 페시아를 장착합니다. 참조 항목: Fascia - Front (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    참고
    전면 페시아 전기 연결부를 연결한 후 절차를 일시 중지하여 소프트웨어 재설치를 시작합니다.
  6. 이 절차의 나머지 단계와 동시에 소프트웨어 재설치를 수행합니다. 참조 항목: Software Reinstall - Touchscreen.
    Informational PurposesAn informational icon, calling your attention
    참고
    소프트웨어 재설치를 시작한 후 전면 페시아 장착을 계속합니다.
  7. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  8. 헤드라이트를 조정합니다.