2023-08-24

Brightwork - Quarter Panel - LH (Remove and Replace)

Correction code 12200702 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices. NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure.NOTE: See 인체공학적 주의 사항for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.

Remove

  1. 외부 스위치를 사용하여 리프트게이트를 엽니다.
  2. LH 상단 브라이트워크를 탈거합니다. Brightwork - Upper - LH (Remove and Replace)을(를) 참조하십시오.
  3. IPA 천을 사용하여 후면 쿼터 차체 글라스의 외부 영역을 닦습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    1분 이상 건조시킵니다.
  4. 후면 쿼터 글라스 차체 영역 주변에 마스킹 테이프를 부착합니다.
  5. 플라스틱 트림 공구를 사용하여 LH 쿼터 브라이트워크를 LH 후면 쿼터 차체 글라스로부터 들어 올린 다음, 접이식 칼날을 사용하여 브라이트워크를 차량에 고정하는 우레탄을 절단합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    절단 도구를 사용할 때에는 항상 절단 방지 장갑을 사용하십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    후면 쿼터 브라이트워크를 LH 상단 차체 측면 브라이트워크에 고정하는 클립에 주의하십시오

Install

  1. IPA 천을 사용하여 우레탄 경로를 닦습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    1분 이상 건조시킵니다.
  2. 캡슐화 글라스 및 LH 쿼터 패널 브라이트워크의 우레탄 경로에 Betaprime 5504G를 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Betaprime은 온도 20˚F(-7˚C) 이상에서 2분 이내에, 0˚F(-18˚C)~20˚F(-7˚C)에서 10분만에 건조됩니다.
  3. 차체에서 마스킹 테이프를 제거합니다.
  4. 코킹 건과 우레탄을 준비합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    우레탄 개구부는 너비가 최대 3.5mm이고 높이가 최대 1.5mm여야 합니다.
  5. 본래의 경로를 따라 쿼터 글라스 씰에 우레탄을 도포합니다.
  6. LH 쿼터 패널 브라이트워크를 차량에 배치한 다음, 완전히 안착하도록 트림에 단단히 누릅니다.
  7. 마스킹 테이프를 사용하여 브라이트워크를 고정합니다.
  8. LH 상단 브라이트워크를 장착합니다. Brightwork - Upper - LH (Remove and Replace)을(를) 참조하십시오.
  9. 리프트게이트를 닫습니다.
  10. 양생 후 테이프를 제거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    양생 시간으로 1시간 이상 여유를 둡니다. 잔여물을 모두 닦아냅니다.