Sensor - Wheel Speed - ABS - Front - LH (Remove and Replace)
Correction code
33100502
0.30
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
- 2024-06-06: 휠 속도 센서 볼트를 일회용 볼트에서 재사용 가능한 볼트로 업데이트하고 토크 규격표를 추가했습니다.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
ABS 휠 속도 센서를 너클에 고정하는 볼트 |
![]() 5 Nm (3.7 lbs-ft) |
|
Reuse |
Remove
- 전면 LH 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
- 전면 LH 휠 아치 라이너를 탈거합니다. 참조 항목: Wheel Arch Liner - Front - LH (Remove and Replace).
-
전면 LH ABS 휠 속도 센서 커넥터에서 전기 하네스를 연결 해제합니다.
-
클립을 분리하고 전면 LH ABS 휠 속도 센서를 차체 및 전면 LH 서스펜션에 고정하는 그로밋을 탈거합니다.
-
전면 LH ABS 휠 속도 센서를 너클에 고정하는 볼트를 탈거한 다음 차량에서 센서를 탈거합니다.
TIpUse of the following tool(s) is recommended:
- 10mm 딥소켓
- 4인치 익스텐션
- 래칫/토크 렌치
Install
-
전면 LH ABS 휠 속도 센서를 너클에 장착한 다음 센서를 너클에 고정하는 볼트를 장착합니다.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 딥소켓
- 4인치 익스텐션
- 래칫/토크 렌치
-
클립(4개)을 조이고 전면 LH ABS 휠 속도 센서 케이블을 차체 및 전면 LH 서스펜션에 고정하는 그로밋을 장착합니다.
경고각 클립 및 그로밋에서 밀고 당기기 확인을 수행하여 차체, 상단 컨트롤 암 및 너클에 완전히 고정되었는지 확인합니다.
-
전기 하네스를 전면 LH ABS 휠 속도 센서 커넥터에 연결합니다.
- 전면 LH 휠 아치 라이너를 장착합니다. 참조 항목: Wheel Arch Liner - Front - LH (Remove and Replace).
- 전면 LH 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
- Perform a test drive that includes a minimum speed of 25mph in straight line for at least five seconds to allow the ESP internal system checks to complete. The ESP faults will clear if the vehicle is repaired correctly. If faults are persistent after the test drive, continue troubleshooting the repair.