2023-12-26

Cover - HV Probe - HV Battery (Remove and Replace)

\Correction code 16101602 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1059330-00-B Skt, 1/4in Dr, 5-Lobe Torx Plus 외부
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Torque Specifications

표 1. Torque Specifications: Cover - HV Probe - HV Battery (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
HV 프로브 커버를 보조 베이 커버에 고정하는 볼트
6 Nm (4.4 lbs-ft)
  • 외부 Torx E10 5-Lobe
  • 4인치 익스텐션
  • 래칫/토크 렌치
Replace
Informational PurposesAn informational icon, calling your attention
참고
Mark the fastener with a paint pen after torquing.

Remove

  1. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  2. HV 프로브 커버를 보조 베이 커버에 고정하는 5-로브 볼트(2개)를 탈거하여 폐기한 후, HV 프로브 커버를 보조 베이 커버에서 탈거합니다.

Install

  1. IPA 천으로 HV 프로브 커버 개스킷 표면 및 보조 베이 커버의 접합면을 소제합니다.
  2. HV 프로브 커버 개스킷과 보조 베이 커버 접합면의 상태를 육안으로 검사하여 균열, 절단, 패임, 마모 또는 씰에 영향을 줄 수 있는 손상이 있는지 점검합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HV 프로브 커버 개스킷이 손상된 경우 개스킷을 교체합니다. 보조 베이 커버 접합면에 씰에 영향을 줄 수 있는 경미한 손상이 있을 경우 지침에 따라 보조 베이 공기 누출 테스트를 수행합니다.
  3. HV 프로브 커버를 보조 베이 커버에 부착하고, HV 프로브 커버를 보조 베이 커버에 고정하는 5-로브 볼트를 장착한 후, 볼트를 토크로 조인 후 페인트 펜으로 볼트에 표시합니다.
    6 Nm (4.4 lbs-ft)
  4. 보조 베이 커버의 접합면에서 약간의 손상이 발견된 경우, 적절한 경우 보조 베이 공기 누출 테스트를 수행합니다. 참조 항목: Ancillary Bay Air Leak Test.
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 베이 커버를 탈거하려는 경우 보조 베이 커버가 장착될 때까지 보조 베이 공기 누출 테스트를 연기합니다.
  5. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).